Bom Samenvattingen, Aantekeningen en Examens

Debate: was dropping the bomb morally justified, because it was the only way to ensure a quick unconditional surrender? To answer, look at • Brutality of Pacific War and the change in balance of power with Soviet entry. • Decision within American High Command about use of bomb(s). • Aftermath of the bombing. • Debates over legitimacy of the bombing, traditional (right) vs revisionist (wrong).

HVAC BOMA Pre-Quiz Latest Version with Complete Solutions Two basic categories of chillers are the _____. Compression cycle and absorption The five requirements for comfort are proper temperature, humidity, filtration, _____. Circulation The primary function of an expansion device is to _____. All of the above (produce a reduction in the pressure on the liquid refrigerant, regulate the flow of refrigerant into the evaporator and lower the boiling point of the refrigerant far enough below ...

OE33a en OE33b in één document samen! OE33a: 8,0 en OE33b: 6,8. Uitgebreide antwoorden op de vragen, geschreven over een Airforce parka jas van de winkel Bomont.

HVAC BOMA 501 Study Guide Latest Update Graded A+ Dual Duct System A system in which hot air and cold air are supplied by separate ducts and mixed at each controlled space to provide the desired supply air temperature. This method consumes a great deal of energy. Muiltizone System an a/c system in which the zone control is obtained by mixing hot and cold air at the unit in response to a room thermostat Load Calulations take the sensible heat and the latent heat into consideration which o...

BOMA - General Maintenance Questions and Answers Graded A+ When starting a centrifugal pump that is part of a manifold with no check valves: You should open the suction valve, start the pump and open the discharge valve slowly A valve inserted in a water line between the corporation stop and the water meter is generally called: Curb cock To check sheave wear: Measure each groove angle Variable pitch sheaves may be used in some cases to provide which of the following types of speed ...

BOMA - Plant Operations Questions and Answers Already Passed 1. How may fittings be attached to a high pressure boiler? Threaded, Certified welds, Flanges Which test determines the relieving capacity of safety valves Accumulation test Flue gasses can leave at high temperatures. We can recover some of this heat using a(n): Economizer Feed water is typically heated with Waste or extracted steam What is the maximum pounds of steam per hour of a boiler called? Boiler capacity ...

BOMA - Instrumentation & Controls Questions and Answers Rated A+ What important function(s) does an air receiver perform? Dissipates heat, Dampens compressor pulsations, Act as water and oil trap On a compressed air system a safety valve would generally be installed on the: Air receiver Variable air volume system: Typically use VFDs to save energy In figure 1.3, a full call for cooling would be at what branch pressure to the damper motor? 3 psig A ratio relay would be used to. Contr...

If created correctly, what document would define the available infrastructure services on an existing wired network? Select one: a. Security Policy b. Request for Proposal (RFP) c. Network Diagram d. Bill of Materials (BoM) - correct answerNetwork Diagram What kind of antenna is most frequently used with indoor APs? Select one: a. Internal b. Parabolic dish c. Yagi d. Grid - correct answerInternal Usin

BOMA-Instrumentation & Controls Questions and Answers Graded A+ A submaster controller resets the set point of the master controller. False Normally open refers to a controlled device that opens when no operating force is applied. True A P.E. Switch is used to change an electrical signal to a pneumatic output. False Moisture and dirt are detrimental to the operation of pneumatic control systems. True A static pressure regulator senses the pressure in the plenum the regulator contro...

WGU C215 Operations Management Exam Prep (Latest 2024/ 2025 Update) | Final Exam Questions and Verified Answers| 100% Correct| Grade A Q: The expected proportion of defective items that will be passed to the customer under the sampling plan. Answer: Average outgoing quality (AOQ) Q: unfilled customer orders Answer: Back orders Q: Delaying delivery to the customer until the item becomes available. Answer: Back-order Q: Owning or controlling sources of raw...