Michigan ASE Brake Certification Study guides, Class notes & Summaries

Michigan ASE Brake Certification Latest Update with Verified Solutions Air in Hydraulic System A spongy brake pedal may be caused by Excessive tire pressure Can not cause very erratic brake pulling while applying brakes Excessive brake pedal travel A power assist brake booster push rod that is too short will cause Brake drum machined beyond its limits Can cause brake pedal fade Repair leak and replace brake linings How to correctly service brake linings soaked with axle greas...

ENGINE REPAIR MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS WHICH OF THE FOLLOWING IS TRUE ABOUT ADJUSTING VALVE TAPPET CLEARANCE - Correct Answer ️️ -A. THE VALVE TAPPET CLEARENCE ON A HIGH MILEAGE EGINE SHOULD BE ADJUSTED TIGHTER THAN SPECIFICATIONS FOR A NEWLY REBUILT ENGINE. B. VALVE TAPPET CLEARANCE SHOULD BE ADJUSTED AT TDC AT THE END OF THE COMPRESSION STROKE. (CORRECT AWNSER) C. VALVE TAPPET CLEARANCE SHOULD BE ADJUSTED AT BDC AT THE END OF THE EXHAUST STROKE. D. N...

HEAVY TRUCK ELECTRICAL MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS THE BATTERY IS CONTINUOUSLY OVERCHARGED. WHAT WILL CAUSE THIS PROBLEM? - Correct Answer ️️ -A. A DEFECTIVE REGULATOR OR ALTERNATOR. (CORRECT AWNSER) B. A WORN OR DAMAGED BATTERY. C. A GROUNDED INDICATOR LIGHT. D. ALL OF THE ABOVE. TO CHECK RESISTANCE IN THE STARTER CIRCUIT, YOU WOULD CONNECT THE NEGATIVE LEAD OF THE VOLT METER TO THE NEGATIVE POST OF THE BATTERY AND THE POSITIVE LEAD OF THE VOLT METER TO:...

STATE BRAKE CERTIFICATION EXAM QUESTIONS AND ANSWERS A cracked or torn vacuum diaphragm in a brake power booster would most likely cause: - Correct Answer ️️ -a hard pedal feel requiring very high pedal effort to stop to test a vacuum power brake booster in the vehicle, you should pump the brake pedal at least 4 times, hold the brake pedal depressed, and start the engine. the brake pedal should: - Correct Answer ️️ -drop slightly and remain firm A mechanic finds gear lube inside b...

AUTOMATIC TRANSMISSIONS MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS WHICH OF THESE PARTS WOULD LIKELY BE FOUND IN THE VALVE BODY? - Correct Answer ️️ -ALL OF THE ABOVE WHAT IS THE FIRST STEP TO PROPERLY DIAGNOSE AN IMPROPERLY SHIFTING TRANSMISSION? - Correct Answer ️️ -A. CHECK THE THROTTLE CABLE ADJUSTMENT (NOT THE ANSWER). B. CHECK THE TORQUE CONVERTER OPERATION C. VERIFY PROPER ENGINE OPERATING CONDITION. (CORRECT AWNSER) D. VERIFY PROPER LINE PRESSURES GEAR TRAIN ...

HEAVY TRUCK BRAKES MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS AN ENGINE BRAKE (JACOBS BRAKE) - Correct Answer ️️ -A. IS A SELF- ENERGIZING SERVO TYPE. B. IS NORMALLY USED IN PLACE OF A SPRING BRAKE. C. RESTRICTS THE INTAKE PORT AND CAUSES A BUILD UP OF 30-45 LBS OF PRESSURE. D. OPENS THE EXHAUST VALVES NEAR THE TOP OF THE COMPRESSION STROKE TO RELEASE THE COMPRESSED AIR. (CORRECT AWNSER) IN THE SYSTEM SHOWN BELOW, THE PART AT C IS: - Correct Answer ️️ -A. AN INVERSI...

HEAVY TRUCK ELECTRICAL MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS THE BATTERY IS CONTINUOUSLY OVERCHARGED. WHAT WILL CAUSE THIS PROBLEM? - Correct Answer ️️ -A. A DEFECTIVE REGULATOR OR ALTERNATOR. (CORRECT AWNSER) B. A WORN OR DAMAGED BATTERY. C. A GROUNDED INDICATOR LIGHT. D. ALL OF THE ABOVE. TO CHECK RESISTANCE IN THE STARTER CIRCUIT, YOU WOULD CONNECT THE NEGATIVE LEAD OF THE VOLT METER TO THE NEGATIVE POST OF THE BATTERY AND THE POSITIVE LEAD OF THE VOLT METER TO:...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...

MANUAL TRANSMISSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS WHEN REPLACING A LEAKING REAR AXEL SEAL, YOU FIND THE AXLE IS PITTED IN THE WHEEL BEARING AREA. WHAT SHOULD YOU DO? - Correct Answer ️️ -A. INSTALL A SLEEVE OVER THE AXEL AND REPLACE THE SEAL. B. INTALL A NEW AXLE, WHEEL BEARING, AND SEAL. (POSSIBLE CORRECT AWNSER) C. POLISH THE AXLE BEFORE INSTALLING IT. D. MACHINE THE AXEL UNDERSIZE, AND REPLACE THE WHEEL BEARING AND SEAL. (NOT CORRECT AWNSER) AS YOU CHECK...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...