Digital circuit Study guides, Class notes & Summaries

An inter-circuit short can cause: - ANSWER -" All of the above; Unrelated circuits to operate simultaneously; Components to work at reduced capacity; An over-current situation" Which of the following is addressed by ABYC A-32? - ANSWER -Power conditioning and conversion LED navigation lights are required to meet: - ANSWER -72 Colregs Which of the following are recommended for 3-phase shore power? - ANSWER -Power conditioning and phase-rotation monitoring Which of the following ...

What is current flow? correct answers D.The flow of electrons in a circuit What is impedance? correct answers A.Opposition to alternating current Like charges will correct answers B.Repel each other Any material that will readily release electrons is called: correct answers B.A conductor The symbol for current is: correct answers B. I Electricity can produce: correct answers D. All the above light heat magnetism The safety ground conductor is usually colored: correct answ...

Spectrum - Field Tech New Hire, Spectrum Field Tech New Hire Week 2 Questions and Answers Already Passed What does the "S" in S.A.F.E stand for? Stop What does the "A" in S.A.F.E stand for? Assess What does the "F" in S.A.F.E stand for? Focus What does the "E" in S.A.F.E stand for? Eliminate What are the three branches of the Safety Triangle? Knowledge Technique Attitude What (in electricity) is the direct cause of injury voltage (E), current (I), or resistance (R)? Current (I) Wha...

Does a fire hood system and a kitchen need to be monitored by the fire alarm system? - Yes What does P.L.F.A stand for? - Power Limited Fire Alarm What does N.P.L.F.A stand for? - Non-Power Limited Fire Alarm What is the difference between P.F.L.A and N.P.F.L.A? - an N.P.L.F.A can operate at up to 600v, and the power output isn't limited a P.L.F.A has the voltage and power limited by a listed power source. What material must N.P.F.L.A circuit conductors be made from? - ONLY solid...

System level design of digital logic circuits using hardwired and programmable logic devices. ROMs, PROMs, and PLAs. Synchronous and asynchronous circuit design and analysis.

If the potential difference across the coil is low, the coil will: A-draw too much current B-become too hot C-Produce too much magnetic force D-not heat up D-not heat up The NEC identifies environments that contain flammable vapors and gases as which class of hazardous location? A-Class I B-Class II C-Class III D-Class IV A-Class I Which of the following reduces high voltages and currents to save values for measurements? A-auto transformer B-megohmmeter C-instrument transf...

CYBR 3210 Study Guide Test 1 Questions & Answers 2024/2025 ATA - ANSWERSAn acronym for Advanced Technology Attachment; the disk drive standard commonly known as Integrated Drive Electronics (IDE) biometrics - ANSWERSThe science and technology of authenticating a person's identity by measuring physiological features. BIOS - ANSWERSAn acronym for basic input/output system; the set of essential software routines that test a PC at start-up and start the OS bus - ANSWERSThe set of har...

PLTW Digital Electronics - Final Review Set 1, PLTW Digital Electronics - Final Review Set 2, PLTW Digital Electronics - Final Review Set 3, Digital Electronics - PLTW Review Test If an integrated circuit has been damaged and you smell smoke, you should__________________. Turn the power off for a few minutes before pulling out the damaged integrated circuit. In scientific notation, which prefixes are used for values smaller than a whole value? Micro, nano, milli What is the value of the r...

Level 1 Module 12 Electrical Test Equipment Questions and Answers 2023 Which of the following devices measures ohms, amps, and volts? Multimeter Which of the following devices is also called an insulation resistance tester? Megger Which instrument should be used to verify that there is power available to run a three-phase motor that will not start? Voltage tester Which meter can measure current without having to make contact with uninsulated wires? Clamp-on anmeter What is the lowest ...

ATT WEEK 10 Exam| Answered 100% Correctly Multiplexing Putting information from several sources on one line of transmission path Demultiplexing Separating info on a single line to several lines or transmission paths Analog to digital AD Circuit that changes analog to digital digital-to-analog converter (DAC) Circuit that changes digital signal to analog Simultaneous a/D converter Uses many comparators and encoders