Study guides, Class notes & Summaries

Steering wheel does not return to center after corner, what is the issue?: A.) binding bearing in steering column B.) loose power steering belt - Binding bearing in the steering column = this would prevent steering wheel from returning to center. Steering wheel shudders while turning, what could be the cause? (Vibrating) A.) air in power steering fluid B.) loose power steering belt - Both= air in power steering fluid would cause cavitation and loss of hydraulic assistance / a slipping and...

ASE A4 Practice Test - ASE A4 Steering and Suspension Test Prep - Test 1 Verified 100% Both A and B - During the visual inspection of a light truck, the technician notices the left rear left spring has a broken center bolt. Technician A says this will affect the vehicle's thrust angle. Technician B says an incorrect thrust angle will affect the centering of the steering wheel. Who is correct? A. Technician A B. Technician B C. Both A and B D. Neither A nor B Raise the vehicle in ...

Raise the vehicle in the air and unload the control arms before torquing them to specifications. - Answer-All of the following are true about control arm bushings EXCEPT: A. Control arm bushings are located between the vehicle's frame and the control arm. B. Worn control arm bushings result in wheel shimmy. C. Raise the vehicle in the air and unload the control arms before torquing them to specifications. D. Control arm bushings reduce friction and isolate vibrations. Technician A - Answ...

ASE A8 VERIFIED 100% SOLUTION spark plug wire resistance should be - ANSWER 5000 to 10000 ohms how do you test spark plug cables insulation - ANSWER spray it with salt water The specification, such as 10 BTDC, indicates that - ANSWER indicates that the spark occurs at 10 degrees before top dead center of the compression stroke With an increase in speed, ignition must begin - ANSWER earlier to end by 23 degrees ATDC Each cylinder must produce power once every - ANSWER 720 degrees what ...

ASE A5 Brakes VERIFIED SOLUTIONS 2023//2024 A hydro-boost brake system has reduced braking performance. Technician A says to check the power steering system. Technician B says to check the vacuum check valve. Who is correct? - ANSWER TECH A is correct. The power steering pump produces pressure for the Hydro-Boost unit. A vehicle with power assisted brakes has a hard brake pedal. Which of the following is LEAST likely to cause this condition? A. Master cylinder. B. Vacuum check va...

ASE A4 Steering and Suspension 100% SOLVED QUESTION AND CORRECT ANSWER Which of the following is the proper way to adjust the rack yoke bearing? A. Tighten to 75 ft lbs. B. Tighten to 5 inch lbs. C. Tighten and then back off the original equipment manufacturer's (OEM) specifications. D. Tighten to 0.002" end-play. - ANSWER Tighten and then back off the originial equipment manufacturer's (OEM) specifications. Many OEMs will recommend that the technician tighten to a specifi...

Which of the following is the proper way to adjust the rack yoke bearing? A. Tighten to 75 ft lbs. B. Tighten to 5 inch lbs. C. Tighten and then back off the original equipment manufacturer's (OEM) specifications. D. Tighten to 0.002" end-play. - ANSWER Tighten and then back off the originial equipment manufacturer's (OEM) specifications. Many OEMs will recommend that the technician tighten to a specification then back off a certain number of degrees. A customer says that the stee...

2. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A and B D. Neither A or B - ANSWER C. Both Techs are right. Too much runout or static out of balance in the front wheels will cause a vibration 3. A vehicle has front wheel sh...

2. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A and B D. Neither A or B C. Both Techs are right. Too much runout or static out of balance in the front wheels will cause a vibration 3. A vehicle has front wheel shimmy at low spe...