NEIEP 200 Final EXAM COMPREHENSIVE QUESTIONS
WITH MULTIPLE CHOICES |VERIFIED & REVISED
ANSWERS (NEW) 2025
19 studiers today Leave the first rating
Save
Students also studied
NEIEP 200 Final EXAM COMPREHE... NEIEP 200 Final Review Relias Dysrhythmia Interpretation NE
Teacher 108 terms 73 terms 36 terms 58
Georges20_ Preview annablake128 Preview sunnydaisy48 Preview
Practice questions for this set
Learn 1 /7 Study with Learn
when installing a reduced stroke buffer, what additional component is required?
Choose an answer
1 test safeties 2 speed limiting device
3 capacity of rigging material 4 counterweight guard
Don't know?
Terms in this set (108)
you are about to loosen a fishplate bolt. a. 6 point box end wrench
which wrench would be least likely to b. 12 point box end wrench
slip? c. open end wrench
you are using a plumb line to check a rail a. the top of the rail needs to go towards the center
for plumb. you find that at the top it b. the top of the rail needs to go toward the wall
measures 1" and at the bottom it measures c. the bottom of the rail needs to go toward the wall
1 1/4". what does this tell you?
you are plumbing rails on a high rise a. nylon string
installation. what type of plumb line b. monofilament wire
should you use? c. piano wire
, you need to cut into a concrete wall. disc grinder with a diamond blade disc
which tool should you use?
you need to select a heavy duty drill for chuck size
drilling 5/8" holes in a machine beam.
what factor determines the drill rating?
you are tasked with setting 3/4" concrete rotary hammer
anchors. which type of drill should you
use?
you need to cut and 8ft section of 1/2" hacksaw with 24 teeth per inch
EMT conduit pipe. what would be the best
tool for the job?
you are directed to move oxy-acetylene in an upright position
cylinders from a storage area to a work
site. what is the proper way to transport
them?
you are setting up welding equipment. 10-12 psi
what is the maximum psi that the regulator
for the acetylene gas may be adjusted
to?
you are using rollers to move a heavy angle front roller gradually and continue around the corner
elevator machine and are approaching a
corner. which technique should you use
to maneuver around it?
you are preparing to unload a truck at the use a steel plate to span the gap
loading dock and the truck is 8" higher
than the dock. what do you do?
you just finished the surface inspection of slightly untwist the strands
a manila rope you will be using for
hoisting. what method should you use to
conduct an internal inspection?
you are preparing to hoist rails and are a light yellow color with a silvery or pearly luster
inspecting your manila rope. which of the
following is a good characteristic of
manila rope?
a mechanic attaches a chainfall to a it is reduced to 50% of original capacity
hoisting beam with a beam clamp. what
happens to the capacity of the hoisting
beam?
you are rigging elevator equipment with a at least 3/4"
sling angle of 60 degrees. you are using a
shouldered eye bolt with a tapped 1/2"
diameter hole. once the shoulder is
seated, what is the minimum thread depth
required?
you will be hoisting 1klbs with a single leg 1k lbs
vertical hitch. what will the sling load be
when the load is in the air
you must attach a wire rope to a load by no nuts on a dead horse
creating a loop with 3 u-bolt wire rope
clips. how should the clips be attached?
you are using a bowline knot- what is one is can easily loosen when not loaded
disadvantage of this knot
WITH MULTIPLE CHOICES |VERIFIED & REVISED
ANSWERS (NEW) 2025
19 studiers today Leave the first rating
Save
Students also studied
NEIEP 200 Final EXAM COMPREHE... NEIEP 200 Final Review Relias Dysrhythmia Interpretation NE
Teacher 108 terms 73 terms 36 terms 58
Georges20_ Preview annablake128 Preview sunnydaisy48 Preview
Practice questions for this set
Learn 1 /7 Study with Learn
when installing a reduced stroke buffer, what additional component is required?
Choose an answer
1 test safeties 2 speed limiting device
3 capacity of rigging material 4 counterweight guard
Don't know?
Terms in this set (108)
you are about to loosen a fishplate bolt. a. 6 point box end wrench
which wrench would be least likely to b. 12 point box end wrench
slip? c. open end wrench
you are using a plumb line to check a rail a. the top of the rail needs to go towards the center
for plumb. you find that at the top it b. the top of the rail needs to go toward the wall
measures 1" and at the bottom it measures c. the bottom of the rail needs to go toward the wall
1 1/4". what does this tell you?
you are plumbing rails on a high rise a. nylon string
installation. what type of plumb line b. monofilament wire
should you use? c. piano wire
, you need to cut into a concrete wall. disc grinder with a diamond blade disc
which tool should you use?
you need to select a heavy duty drill for chuck size
drilling 5/8" holes in a machine beam.
what factor determines the drill rating?
you are tasked with setting 3/4" concrete rotary hammer
anchors. which type of drill should you
use?
you need to cut and 8ft section of 1/2" hacksaw with 24 teeth per inch
EMT conduit pipe. what would be the best
tool for the job?
you are directed to move oxy-acetylene in an upright position
cylinders from a storage area to a work
site. what is the proper way to transport
them?
you are setting up welding equipment. 10-12 psi
what is the maximum psi that the regulator
for the acetylene gas may be adjusted
to?
you are using rollers to move a heavy angle front roller gradually and continue around the corner
elevator machine and are approaching a
corner. which technique should you use
to maneuver around it?
you are preparing to unload a truck at the use a steel plate to span the gap
loading dock and the truck is 8" higher
than the dock. what do you do?
you just finished the surface inspection of slightly untwist the strands
a manila rope you will be using for
hoisting. what method should you use to
conduct an internal inspection?
you are preparing to hoist rails and are a light yellow color with a silvery or pearly luster
inspecting your manila rope. which of the
following is a good characteristic of
manila rope?
a mechanic attaches a chainfall to a it is reduced to 50% of original capacity
hoisting beam with a beam clamp. what
happens to the capacity of the hoisting
beam?
you are rigging elevator equipment with a at least 3/4"
sling angle of 60 degrees. you are using a
shouldered eye bolt with a tapped 1/2"
diameter hole. once the shoulder is
seated, what is the minimum thread depth
required?
you will be hoisting 1klbs with a single leg 1k lbs
vertical hitch. what will the sling load be
when the load is in the air
you must attach a wire rope to a load by no nuts on a dead horse
creating a loop with 3 u-bolt wire rope
clips. how should the clips be attached?
you are using a bowline knot- what is one is can easily loosen when not loaded
disadvantage of this knot
