MICHIGAN STATE BRAKES CERTIFICATION TEST
FINAL EXAM 2025/2026 ACTUAL EXAM
COMPLETE 200 EXAM QUESTIONS WITH
DETAILED VERIFIED ANSWERS (100% CORRECT
ANSWERS) /LATEST UPDATE ALREADY GRADED
A+
Which of the following is not a necessary precaution to
follow when performing brake repairs on an ABS equipped
vehicle? - ....ANSWER...Always remove the electronic
brake control module fuse before adjusting or replacing a
wheel speed sensor
Which of the following is true when inspecting wheel speed
sensors? - ....ANSWER...You should measure the air
gap between the sensor and the reluctor wheel
teeth
Which of the following would be the result of an
inoperative ABS pump/motor assembly: -
....ANSWER...Conventional braking should still be
available
1
,What information might be found on a brake drum to help
a mechanic? - ....ANSWER...The maximum diameter
dimension
When checking a newly turned drum before putting it
back on, you notice a thread-like grooves in the braking
surface. Why are the grooves there? -
....ANSWER...The lathe was not adjusted
properly when the drum was turned
A cracked or torn vacuum diaphragm in a brake power
booster would most likely cause: - ....ANSWER...a hard
pedal feel requiring very high pedal effort to stop
to test a vacuum power brake booster in the vehicle, you
should pump the brake pedal at least 4 times, hold the
brake pedal depressed, and start the engine. the brake
pedal should: - ....ANSWER...drop slightly and
remain firm
A mechanic finds gear lube inside both rear drums on a
rear wheel drive vehicle. What is most likely the cause of
this problem? - ....ANSWER...a plugged axle
2
, On a vehicle with a disc/drum brake system, the rear
wheels lock up under hard braking. The most likely cause
is: - ....ANSWER...A defective proportioning valve
After putting a bearing race in a hub, you notice that the
new race is loose and can spin in the hub. What should you
do? - ....ANSWER...Replace the hub
When adjusting disc-drum brakes, you should: -
....ANSWER...Adjust the rear brakes after releasing the
parking brakes
You are rebuilding a master cylinder. What should you use
to lubricate the internal parts? - ....ANSWER...Brake fluid
3
FINAL EXAM 2025/2026 ACTUAL EXAM
COMPLETE 200 EXAM QUESTIONS WITH
DETAILED VERIFIED ANSWERS (100% CORRECT
ANSWERS) /LATEST UPDATE ALREADY GRADED
A+
Which of the following is not a necessary precaution to
follow when performing brake repairs on an ABS equipped
vehicle? - ....ANSWER...Always remove the electronic
brake control module fuse before adjusting or replacing a
wheel speed sensor
Which of the following is true when inspecting wheel speed
sensors? - ....ANSWER...You should measure the air
gap between the sensor and the reluctor wheel
teeth
Which of the following would be the result of an
inoperative ABS pump/motor assembly: -
....ANSWER...Conventional braking should still be
available
1
,What information might be found on a brake drum to help
a mechanic? - ....ANSWER...The maximum diameter
dimension
When checking a newly turned drum before putting it
back on, you notice a thread-like grooves in the braking
surface. Why are the grooves there? -
....ANSWER...The lathe was not adjusted
properly when the drum was turned
A cracked or torn vacuum diaphragm in a brake power
booster would most likely cause: - ....ANSWER...a hard
pedal feel requiring very high pedal effort to stop
to test a vacuum power brake booster in the vehicle, you
should pump the brake pedal at least 4 times, hold the
brake pedal depressed, and start the engine. the brake
pedal should: - ....ANSWER...drop slightly and
remain firm
A mechanic finds gear lube inside both rear drums on a
rear wheel drive vehicle. What is most likely the cause of
this problem? - ....ANSWER...a plugged axle
2
, On a vehicle with a disc/drum brake system, the rear
wheels lock up under hard braking. The most likely cause
is: - ....ANSWER...A defective proportioning valve
After putting a bearing race in a hub, you notice that the
new race is loose and can spin in the hub. What should you
do? - ....ANSWER...Replace the hub
When adjusting disc-drum brakes, you should: -
....ANSWER...Adjust the rear brakes after releasing the
parking brakes
You are rebuilding a master cylinder. What should you use
to lubricate the internal parts? - ....ANSWER...Brake fluid
3
