EBOLC Project Management LATEST UPDATED exam
WITH COMPLETE questions and VERIFIED answers
100% GUARANTEED PASS!!
1. When taping a blasting cap to a line or ring main, how much of the
cap needs to be exposed on each side? - ANSWER 1/8 and 1/4 Inch
2. When priming a Bangalore with M456 Det Cord, how many wraps
do you need on the bottom? - ANSWER 8
3. Where are the boosters located on the Bangalore Torpedo? How
long are they? - ANSWER On each end of the Bangalore. They are
4 Inches long.
4. Explosives that are considered block in form are: - ANSWER C4
and TNT
5. The explosive that is considered cylindrical in form is: - ANSWER
M1 Dynamite
6. The correct term for "the shattering effect of explosives in relation
to that of TNT" is known as what? - ANSWER The Relative
Effectiveness (RE) Factor
7. The part of the Basic Demo System that is responsible for carrying
the pressure wave from the Initiation System to the Primary Charge
is the _______. - ANSWER Firing System
, 8. Your line main or ring main must be made of what? - ANSWER
Det Cord
9. List the types of high-strength blasting caps. - ANSWER M11,
M14, M18, M19, M21, M23
10.List the types of low-strength blasting caps. - ANSWER M12, M13
11.Never attach M456 Det Cord, an M151, or an M152 to this
component. - ANSWER M81
12.An _________ can accommodate and ensure proper proximity for
initiating up to 5 shock tubes, 5 M151/152's OR 1 strand of M456
Det Cord. - ANSWER M9 Holder
13.This component has a high-strength blasting cap, factory-crimped
to a 30-ft length of shock tube. It also has a small J-hook for easy
attachment to M456 Let Cord, a yellow flag 2 meters from the
blasting cap and a red flag 1 meter from the blasting cap. -
ANSWER M11
14.An _____ has a high-strength blasting cap, factory-crimped to
about 7.5 ft length of time fuse that has a 5 minute burn time. -
ANSWER M14
15.When priming a block of C4 (M112), using M456 Det Cord, what
knot is used below freezing? - ANSWER Uli Knot
WITH COMPLETE questions and VERIFIED answers
100% GUARANTEED PASS!!
1. When taping a blasting cap to a line or ring main, how much of the
cap needs to be exposed on each side? - ANSWER 1/8 and 1/4 Inch
2. When priming a Bangalore with M456 Det Cord, how many wraps
do you need on the bottom? - ANSWER 8
3. Where are the boosters located on the Bangalore Torpedo? How
long are they? - ANSWER On each end of the Bangalore. They are
4 Inches long.
4. Explosives that are considered block in form are: - ANSWER C4
and TNT
5. The explosive that is considered cylindrical in form is: - ANSWER
M1 Dynamite
6. The correct term for "the shattering effect of explosives in relation
to that of TNT" is known as what? - ANSWER The Relative
Effectiveness (RE) Factor
7. The part of the Basic Demo System that is responsible for carrying
the pressure wave from the Initiation System to the Primary Charge
is the _______. - ANSWER Firing System
, 8. Your line main or ring main must be made of what? - ANSWER
Det Cord
9. List the types of high-strength blasting caps. - ANSWER M11,
M14, M18, M19, M21, M23
10.List the types of low-strength blasting caps. - ANSWER M12, M13
11.Never attach M456 Det Cord, an M151, or an M152 to this
component. - ANSWER M81
12.An _________ can accommodate and ensure proper proximity for
initiating up to 5 shock tubes, 5 M151/152's OR 1 strand of M456
Det Cord. - ANSWER M9 Holder
13.This component has a high-strength blasting cap, factory-crimped
to a 30-ft length of shock tube. It also has a small J-hook for easy
attachment to M456 Let Cord, a yellow flag 2 meters from the
blasting cap and a red flag 1 meter from the blasting cap. -
ANSWER M11
14.An _____ has a high-strength blasting cap, factory-crimped to
about 7.5 ft length of time fuse that has a 5 minute burn time. -
ANSWER M14
15.When priming a block of C4 (M112), using M456 Det Cord, what
knot is used below freezing? - ANSWER Uli Knot
