10/31/25, 1:32 PM S-95 FDNY TEST STUDY GUIDE Exam comprehensive questions | FREQUENTLY MOST TESTED QUESTIONS AND VERIFIE…
S-95 FDNY TEST STUDY GUIDE Exam
comprehensive questions | FREQUENTLY MOST
TESTED QUESTIONS AND VERIFIED
SOLUTIONS/GET IT 100% ACCURATE!! 2025!!
Save
Terms in this set (55)
What Can A S95 Holder Only visual inspections on smoke alarms
do?
on a premise is to warn tenants and transmit signals
Primary Purpose of Fire
indicating a fire condition to the FDNY aka Central
Alarm Systems
station
Monitors inputs and controls output through various
Fire Alarm Control Panel types of circuits.The Panel activates the building
(FACP) audible and visual device connected to the fire alarm
(horn/strobes)
Fire Alarm Signal, Supervisory Signals, and Trouble
Three Types of Signals
Signals
Manual fire alarm pull station, smoke detector, water
Fire Alarm Signal flow switch in the
presence of a fire or fire signature.
https://quizlet.com/1101337633/s-95-fdny-test-study-guide-exam-comprehensive-questions-frequently-most-tested-questions-and-verified-solutionsget… 1/9
, 10/31/25, 1:32 PM S-95 FDNY TEST STUDY GUIDE Exam comprehensive questions | FREQUENTLY MOST TESTED QUESTIONS AND VERIFIE…
Signals which Indicate that a system or device being
monitored has been compromised or is in an
abnormal state. Will audibly and visually annunciate at
Supervisory Signals
the FACP to indicate the condition needs to be
investigated and corrected. The FACP will also send a
signal to an FDNY approved central station.
Battery failure, AC failure, ground fault, open or short
Trouble Signals circuit on a wire, phone line failure, internal
component failure.
Is used to silence the building audible and visual
devices after evacuation is complete while the source
Alarm Silence Switch or
of alarm is being investigated. Never reset the fire
Button
alarm system until the condition is verified by the
FDNY personnel.
Reset fire alarm system after condition is cleared.
System Reset Switch Or Should return to normal condition after resetting.
Button Often required to clear supervisory conditions, does
not clear trouble conditions.
Cleaned once every 6 months. Test for smoke entry
Smoke detectors must be
every once a year
shall be generated electric power not exceeding
Primary Power
277/480 volts
Batteries shall not be a sub for connection to the
Secondary Power Source
secondary source
Manual Pull Return handle to normal position. A key or other
Station~Manually pulling method may be required to reset the station to
handle normal
Smoke, beam, and duct Smoke detectors will normally reset when the reset
detectors~ Detection of button is pressed at the FACP if the condition
particles of combustion activating the detector has been cleared
https://quizlet.com/1101337633/s-95-fdny-test-study-guide-exam-comprehensive-questions-frequently-most-tested-questions-and-verified-solutionsget… 2/9
S-95 FDNY TEST STUDY GUIDE Exam
comprehensive questions | FREQUENTLY MOST
TESTED QUESTIONS AND VERIFIED
SOLUTIONS/GET IT 100% ACCURATE!! 2025!!
Save
Terms in this set (55)
What Can A S95 Holder Only visual inspections on smoke alarms
do?
on a premise is to warn tenants and transmit signals
Primary Purpose of Fire
indicating a fire condition to the FDNY aka Central
Alarm Systems
station
Monitors inputs and controls output through various
Fire Alarm Control Panel types of circuits.The Panel activates the building
(FACP) audible and visual device connected to the fire alarm
(horn/strobes)
Fire Alarm Signal, Supervisory Signals, and Trouble
Three Types of Signals
Signals
Manual fire alarm pull station, smoke detector, water
Fire Alarm Signal flow switch in the
presence of a fire or fire signature.
https://quizlet.com/1101337633/s-95-fdny-test-study-guide-exam-comprehensive-questions-frequently-most-tested-questions-and-verified-solutionsget… 1/9
, 10/31/25, 1:32 PM S-95 FDNY TEST STUDY GUIDE Exam comprehensive questions | FREQUENTLY MOST TESTED QUESTIONS AND VERIFIE…
Signals which Indicate that a system or device being
monitored has been compromised or is in an
abnormal state. Will audibly and visually annunciate at
Supervisory Signals
the FACP to indicate the condition needs to be
investigated and corrected. The FACP will also send a
signal to an FDNY approved central station.
Battery failure, AC failure, ground fault, open or short
Trouble Signals circuit on a wire, phone line failure, internal
component failure.
Is used to silence the building audible and visual
devices after evacuation is complete while the source
Alarm Silence Switch or
of alarm is being investigated. Never reset the fire
Button
alarm system until the condition is verified by the
FDNY personnel.
Reset fire alarm system after condition is cleared.
System Reset Switch Or Should return to normal condition after resetting.
Button Often required to clear supervisory conditions, does
not clear trouble conditions.
Cleaned once every 6 months. Test for smoke entry
Smoke detectors must be
every once a year
shall be generated electric power not exceeding
Primary Power
277/480 volts
Batteries shall not be a sub for connection to the
Secondary Power Source
secondary source
Manual Pull Return handle to normal position. A key or other
Station~Manually pulling method may be required to reset the station to
handle normal
Smoke, beam, and duct Smoke detectors will normally reset when the reset
detectors~ Detection of button is pressed at the FACP if the condition
particles of combustion activating the detector has been cleared
https://quizlet.com/1101337633/s-95-fdny-test-study-guide-exam-comprehensive-questions-frequently-most-tested-questions-and-verified-solutionsget… 2/9
