AFAB 110 STUDY GUIDE QUESTIONS AND SOLUTIONS
RATED A+
✔✔On a print a ____ provides a larger assembly - ✔✔application block
✔✔An assembly drawing contains only the ____ lines critical to explaining how the
parts are assembled - ✔✔Hidden
✔✔A ____ assembly drawing is a drawing composed of two or more parts that, once
assembled. - ✔✔INSEPARABLE DRAWING
✔✔One type of drawing that takes on the appearance of an assembly drawing is a
_____ drawing. - ✔✔Welding drawing
✔✔Drawings apply dimensions to the shape of a part while it is a flat piece of metal or
other stock. - ✔✔Pattern Development
✔✔Drawings created to document the engineering requirements of a purchased part
are called ____ drawings. - ✔✔Controlled
✔✔The standard term for one detailed drawing of one part is a ____ drawing. -
✔✔MONO DETAILED
✔✔A term used in some companies for a temporary revision that authorizes a deviation
from the print is a___ - ✔✔DRAWING DEVIATION
✔✔In the not-to-scale method a ___ line is drawn below the dimension value of the
revised feature. - ✔✔HEAVY
✔✔ECO - ✔✔Engineering change order
✔✔Double feature layer - ✔✔Composite
✔✔Which of the following geometric controlled is discontinued from the current
something - ✔✔Concentricity
✔✔A geometric tolerance something on datum axis dial indicator - ✔✔RUNOUT
✔✔Which of the following geometric control is not a orientation - ✔✔Circularity
✔✔A blank dimensions feature a the theoretically exact location of a feature axis or
median plane is known as - ✔✔Basic Position
, ✔✔Which of the following is not found on a feature control frame - ✔✔Surface Texture
Symbol
✔✔Which of the following is not a choice for placing a surface texture symbol on a print
- ✔✔CENTERLINE OF A CYLINDER
✔✔Which of the following is not one of the 7 lay symbol. - ✔✔An "L"
✔✔The term ____ is used to describe an unintentional interruption of the surface. -
✔✔A FLAW
✔✔Before the development of the current surface texture symbol an italic ___ symbol
indicates - ✔✔An "F"
✔✔Beveled edges of parts are called - ✔✔Beveled Chamfords
✔✔Which of the following is not a term for additional annotations on a drawing -
✔✔PROCESSES
✔✔For a hole that is 1.500"-1.508" mating with a shaft that is 1.475"-1.485" the limits of
clearance are - ✔✔C-.015"-0.33"
✔✔If an engineer specifies an RC3 class fit for a 1" assuming the basic hole is - ✔✔1
INCH HOLE
✔✔A tolerance method that incorporates the MIN or MAX note is referred to as ____ -
✔✔SINGLE LIMIT
✔✔A __ symbol is indicated by a letter in the box attached to the views - ✔✔A DATUM
✔✔The ___ of a feature is the size limit representing the feature when the most material
is present - ✔✔Maximum material condition
✔✔Which of the following is an example of a bilateral tolerance - ✔✔+-.005"
✔✔An un dimension drawing defines the part with a - ✔✔TRUE GEOMETRY VIEW
✔✔Dimensioning, the alternate part is commonly placed in brackets following the
primary value - ✔✔Dual
RATED A+
✔✔On a print a ____ provides a larger assembly - ✔✔application block
✔✔An assembly drawing contains only the ____ lines critical to explaining how the
parts are assembled - ✔✔Hidden
✔✔A ____ assembly drawing is a drawing composed of two or more parts that, once
assembled. - ✔✔INSEPARABLE DRAWING
✔✔One type of drawing that takes on the appearance of an assembly drawing is a
_____ drawing. - ✔✔Welding drawing
✔✔Drawings apply dimensions to the shape of a part while it is a flat piece of metal or
other stock. - ✔✔Pattern Development
✔✔Drawings created to document the engineering requirements of a purchased part
are called ____ drawings. - ✔✔Controlled
✔✔The standard term for one detailed drawing of one part is a ____ drawing. -
✔✔MONO DETAILED
✔✔A term used in some companies for a temporary revision that authorizes a deviation
from the print is a___ - ✔✔DRAWING DEVIATION
✔✔In the not-to-scale method a ___ line is drawn below the dimension value of the
revised feature. - ✔✔HEAVY
✔✔ECO - ✔✔Engineering change order
✔✔Double feature layer - ✔✔Composite
✔✔Which of the following geometric controlled is discontinued from the current
something - ✔✔Concentricity
✔✔A geometric tolerance something on datum axis dial indicator - ✔✔RUNOUT
✔✔Which of the following geometric control is not a orientation - ✔✔Circularity
✔✔A blank dimensions feature a the theoretically exact location of a feature axis or
median plane is known as - ✔✔Basic Position
, ✔✔Which of the following is not found on a feature control frame - ✔✔Surface Texture
Symbol
✔✔Which of the following is not a choice for placing a surface texture symbol on a print
- ✔✔CENTERLINE OF A CYLINDER
✔✔Which of the following is not one of the 7 lay symbol. - ✔✔An "L"
✔✔The term ____ is used to describe an unintentional interruption of the surface. -
✔✔A FLAW
✔✔Before the development of the current surface texture symbol an italic ___ symbol
indicates - ✔✔An "F"
✔✔Beveled edges of parts are called - ✔✔Beveled Chamfords
✔✔Which of the following is not a term for additional annotations on a drawing -
✔✔PROCESSES
✔✔For a hole that is 1.500"-1.508" mating with a shaft that is 1.475"-1.485" the limits of
clearance are - ✔✔C-.015"-0.33"
✔✔If an engineer specifies an RC3 class fit for a 1" assuming the basic hole is - ✔✔1
INCH HOLE
✔✔A tolerance method that incorporates the MIN or MAX note is referred to as ____ -
✔✔SINGLE LIMIT
✔✔A __ symbol is indicated by a letter in the box attached to the views - ✔✔A DATUM
✔✔The ___ of a feature is the size limit representing the feature when the most material
is present - ✔✔Maximum material condition
✔✔Which of the following is an example of a bilateral tolerance - ✔✔+-.005"
✔✔An un dimension drawing defines the part with a - ✔✔TRUE GEOMETRY VIEW
✔✔Dimensioning, the alternate part is commonly placed in brackets following the
primary value - ✔✔Dual
