Trade related preparation questions
and answers rated A+
the least common multiple of 3, 4, 6 and 8 is? - correct answer ✔✔ 24
the communitive property states that - correct answer ✔✔ the order in which you add the
numbers doesn't affect the sum
you use a micrometer to measure a part. To obtain the full inch reading, you'll refer to the -
correct answer ✔✔ size of the micrometer being used
Each graduation on the thimble of a metric micrometer is equal to - correct answer ✔✔ 0.010
if you suspect the edge of your rule has a rounded corner from use, you should. - correct
answer ✔✔ overlap the edge of the work peace with the rule and measure from another
graduation.
a feeler gage may be made out of - correct answer ✔✔ metal leaves or wires
Spring and transfer calipers provide - correct answer ✔✔ indirect measurement
What are the four kinds of measurements that can be made with most calipers? - correct
answer ✔✔ Step, inside, outside, depth
a dial would provide an_________ measurement - correct answer ✔✔ direct
what should you use to measure the inside diameter of an aluminum cylinder. - correct answer
✔✔ The ears of a dial caliper
, Base unit of length in metric system is the - correct answer ✔✔ Meter
what is the metric equivalent to a 6in. English rule? - correct answer ✔✔ A 15.24cm rule
Each line on the Vernier scale provided equals - correct answer ✔✔ 0.001
a cylindrical square is capable of creaking in units of - correct answer ✔✔ 0.0002
A drill point gage is used to - correct answer ✔✔ ensure that the correct angle and lengths are
grounded on the drill.
Decimal dimensions are used on shop drawings because - correct answer ✔✔ decimals are
easier to add together
What is precision? - correct answer ✔✔ The ability to get the same answer each time you
measure an object
The purpose of closing calipers before using them is to - correct answer ✔✔ check the zero
setting of the caliper
The ground and graduated main vial of a master precision level is of __________ accuracy -
correct answer ✔✔ 10 seconds
In machine shops, the most common unit of measurement in the metric system is the - correct
answer ✔✔ millimeter
and answers rated A+
the least common multiple of 3, 4, 6 and 8 is? - correct answer ✔✔ 24
the communitive property states that - correct answer ✔✔ the order in which you add the
numbers doesn't affect the sum
you use a micrometer to measure a part. To obtain the full inch reading, you'll refer to the -
correct answer ✔✔ size of the micrometer being used
Each graduation on the thimble of a metric micrometer is equal to - correct answer ✔✔ 0.010
if you suspect the edge of your rule has a rounded corner from use, you should. - correct
answer ✔✔ overlap the edge of the work peace with the rule and measure from another
graduation.
a feeler gage may be made out of - correct answer ✔✔ metal leaves or wires
Spring and transfer calipers provide - correct answer ✔✔ indirect measurement
What are the four kinds of measurements that can be made with most calipers? - correct
answer ✔✔ Step, inside, outside, depth
a dial would provide an_________ measurement - correct answer ✔✔ direct
what should you use to measure the inside diameter of an aluminum cylinder. - correct answer
✔✔ The ears of a dial caliper
, Base unit of length in metric system is the - correct answer ✔✔ Meter
what is the metric equivalent to a 6in. English rule? - correct answer ✔✔ A 15.24cm rule
Each line on the Vernier scale provided equals - correct answer ✔✔ 0.001
a cylindrical square is capable of creaking in units of - correct answer ✔✔ 0.0002
A drill point gage is used to - correct answer ✔✔ ensure that the correct angle and lengths are
grounded on the drill.
Decimal dimensions are used on shop drawings because - correct answer ✔✔ decimals are
easier to add together
What is precision? - correct answer ✔✔ The ability to get the same answer each time you
measure an object
The purpose of closing calipers before using them is to - correct answer ✔✔ check the zero
setting of the caliper
The ground and graduated main vial of a master precision level is of __________ accuracy -
correct answer ✔✔ 10 seconds
In machine shops, the most common unit of measurement in the metric system is the - correct
answer ✔✔ millimeter
