FUSION360 STUDY GUIDE 2025/2026 QUESTIONS AND
SOLUTION RATED A+
✔✔Which Circular Pattern option was used in this sketch? - ✔✔Suppress
✔✔A mechanical engineer would like to create an exploded view drawing of an
assembly from an animation storyboard.
What component positions are used as reference in the resulting exploded view
drawing? - ✔✔Positions at the end of the story board
✔✔What can be changed to make exhibit 1 look like exhibit 2? - ✔✔Roughness
✔✔A mechanical engineer is designing a component to be manufactured out of a
tungsten alloy using an SLM printer.
How can the mechanical engineer accurately determine which orientation has the
lowest center of mass (CoM) using the component properties? - ✔✔Place the height
component on the XY Plane for each orientation and record the CoM Z height
✔✔A mechanical engineer was provided with an assembly of a mechanical pencil, as
seen in exhibit 1.The mechanical engineer plans to use the assembly, as seen in exhibit
2, each component moves separately.
What assembly tool could connect every component together in one feature? - ✔✔Rigid
Group
✔✔A mechanical engineer is creating a tilt-adjustable assembly and would like to define
joints to control motion between the components.
Which of the following joint types would allow for 1 degree of translation and 1 degree of
rotation between the holder and the cutout in the base for the needed motion as shown
in the exhibit? - ✔✔Pin-Slot
✔✔A mechanical engineer is working with a form body to create a complex body panel
for a vehicle.The mechanical engineer is using the Bevel Edge tool to create a sharper
transition on the shape.Exhibit 1 is the original freeform body. Exhibit 2 has a relative
offset bevel tool added, and exhibit 3 has the same edge with only one variable
changed.
Which setting in the dialog was altered between the beveled edges created in exhibit 2?
- ✔✔Crown
✔✔A mechanical engineer is creating a flange with the Extrude tool as shown in the
exhibit.
Which two extrude options are needed to create the flange in a single operation?
(Select two.) - ✔✔Taper Angle AND Thin Extrude
, ✔✔A mechanical engineer is tasked with designing an acoustic guitar. - ✔✔Blend
Curve
✔✔A rectangular pattern has been created to control hole placement by referencing
predefined User Parameters shown in exhibit 1. However, when the mechanical
engineer changes the length of the plate as seen in exhibit 2, the Rectangular Pattern
dialog in exhibit 3 produces an error in the Quantity field due the specified value being a
decimal.
Which of the following modifications will ensure that the HoleQty parameter is always
computed to be the number of complete holes that can fit on the plate without
overlapping? - ✔✔Wrap the HoleQty expression in a floor() function.
✔✔A mechanical engineer is creating a base plate that will contain a set of mounting
holes based on the base plate's size. The mechanical engineer needs to ensure the
number of holes in the length direction matches the number of holes in the width
direction. What should the equation be for the user parameter for hole spacing in the
width direction? - ✔✔BaseWidth / 10
✔✔ A mechanical engineer is reviewing a design for CNC Milling using the Minimum
Radius Analysis tool.
Based on the exhibit, which available endmill should be used to finish the pocket? -
✔✔0.5 in. (12 mm) Flat Endmill
✔✔A mechanical engineer is tasked with designing a plastic container with 2 degrees of
draft.
The mechanical engineer sets the Draft Analysis tool to +- 2 degrees with a tolerance
zone of 0.5 degrees.
Why are the inside faces of the design shown in yellow when viewing the draft analysis?
- ✔✔They are within the tolerance zone.
✔✔A mechanical engineer is starting a new sheet metal component in Fusion and
editing the sheet metal rule.
Which sheet metal rule value determines where the neutral axis will be on a sheet metal
part? - ✔✔K Factor
✔✔A mechanical engineer has created a rectangular sketch pattern of hexagons, as
shown in the exhibit.
The rectangular pattern has been defined with the proper quantity and spacing,
however the sketch remains undefined.
Which of the following actions will fully define the sketch? - ✔✔Apply a collinear
constraint between points A, D, and origin E
✔✔A mechanical engineer has defined a hole using the Hole tool. Which of the holes
pictured in the exhibit corresponds to the Hole dialog? - ✔✔Hole 3
SOLUTION RATED A+
✔✔Which Circular Pattern option was used in this sketch? - ✔✔Suppress
✔✔A mechanical engineer would like to create an exploded view drawing of an
assembly from an animation storyboard.
What component positions are used as reference in the resulting exploded view
drawing? - ✔✔Positions at the end of the story board
✔✔What can be changed to make exhibit 1 look like exhibit 2? - ✔✔Roughness
✔✔A mechanical engineer is designing a component to be manufactured out of a
tungsten alloy using an SLM printer.
How can the mechanical engineer accurately determine which orientation has the
lowest center of mass (CoM) using the component properties? - ✔✔Place the height
component on the XY Plane for each orientation and record the CoM Z height
✔✔A mechanical engineer was provided with an assembly of a mechanical pencil, as
seen in exhibit 1.The mechanical engineer plans to use the assembly, as seen in exhibit
2, each component moves separately.
What assembly tool could connect every component together in one feature? - ✔✔Rigid
Group
✔✔A mechanical engineer is creating a tilt-adjustable assembly and would like to define
joints to control motion between the components.
Which of the following joint types would allow for 1 degree of translation and 1 degree of
rotation between the holder and the cutout in the base for the needed motion as shown
in the exhibit? - ✔✔Pin-Slot
✔✔A mechanical engineer is working with a form body to create a complex body panel
for a vehicle.The mechanical engineer is using the Bevel Edge tool to create a sharper
transition on the shape.Exhibit 1 is the original freeform body. Exhibit 2 has a relative
offset bevel tool added, and exhibit 3 has the same edge with only one variable
changed.
Which setting in the dialog was altered between the beveled edges created in exhibit 2?
- ✔✔Crown
✔✔A mechanical engineer is creating a flange with the Extrude tool as shown in the
exhibit.
Which two extrude options are needed to create the flange in a single operation?
(Select two.) - ✔✔Taper Angle AND Thin Extrude
, ✔✔A mechanical engineer is tasked with designing an acoustic guitar. - ✔✔Blend
Curve
✔✔A rectangular pattern has been created to control hole placement by referencing
predefined User Parameters shown in exhibit 1. However, when the mechanical
engineer changes the length of the plate as seen in exhibit 2, the Rectangular Pattern
dialog in exhibit 3 produces an error in the Quantity field due the specified value being a
decimal.
Which of the following modifications will ensure that the HoleQty parameter is always
computed to be the number of complete holes that can fit on the plate without
overlapping? - ✔✔Wrap the HoleQty expression in a floor() function.
✔✔A mechanical engineer is creating a base plate that will contain a set of mounting
holes based on the base plate's size. The mechanical engineer needs to ensure the
number of holes in the length direction matches the number of holes in the width
direction. What should the equation be for the user parameter for hole spacing in the
width direction? - ✔✔BaseWidth / 10
✔✔ A mechanical engineer is reviewing a design for CNC Milling using the Minimum
Radius Analysis tool.
Based on the exhibit, which available endmill should be used to finish the pocket? -
✔✔0.5 in. (12 mm) Flat Endmill
✔✔A mechanical engineer is tasked with designing a plastic container with 2 degrees of
draft.
The mechanical engineer sets the Draft Analysis tool to +- 2 degrees with a tolerance
zone of 0.5 degrees.
Why are the inside faces of the design shown in yellow when viewing the draft analysis?
- ✔✔They are within the tolerance zone.
✔✔A mechanical engineer is starting a new sheet metal component in Fusion and
editing the sheet metal rule.
Which sheet metal rule value determines where the neutral axis will be on a sheet metal
part? - ✔✔K Factor
✔✔A mechanical engineer has created a rectangular sketch pattern of hexagons, as
shown in the exhibit.
The rectangular pattern has been defined with the proper quantity and spacing,
however the sketch remains undefined.
Which of the following actions will fully define the sketch? - ✔✔Apply a collinear
constraint between points A, D, and origin E
✔✔A mechanical engineer has defined a hole using the Hole tool. Which of the holes
pictured in the exhibit corresponds to the Hole dialog? - ✔✔Hole 3
