Neiep 515 Piping and Wiring The Car Ques ons And
Complete Verified Solu ons 2025.
One-half - Answer The Loop that is formed in the traveling cables at _______ the speed of the
car
Bracke ng a ached to the guide rail, the hoistway wall, or the building structure - Answer The
sta onary end of the traveling cable is fastened to _______, _______, or _______
Signal - Answer Each wire carries a specific electrical ________ between the car and the
machine room controls
Strain wire - Answer The steel core is called the _______
Reduce fric on and enhance flexibility - Answer Jute fibers are included to _______ and
_______
Torsional stress - Answer Before they are permanently installed, traveling cables should be hung
free in order to relieve _______
Spool - Answer On Lengths up to 100 feet _______ supports may be used
200 Feet - Answer On lengths over _______ the strain wire must be used for suspension
Junc on box - Answer At the permanent suspension point in the hoistway, slightly above the
center of travel, an electrical _______ may be installed
, 200 - Answer Cable grippers may be used to suspend up to _______ feet of traveling cable
Controller - Answer On a low-rise installa on, such as a hydraulic elevator, the traveling cables
may run to the _______
Fully compressed buffer - Answer On a high rise elevator with a deep pit, the reference point for
the lop in the traveling cable will be above the pit floor, where the car rests on the _______
Reel rollers, reel jacks, saw horses - Answer When the traveling cable is received on reels, the
reels can be set up on _______, _______, _______
Split cable gripper and swivel link - Answer When raising traveling cables with a hois ng line,
the line should be connected with a _______
Public safety - Answer On a cable replacement job, in an occupied building, the thing to keep
uppermost in your mind is _______
Brackets, switches, buffers - Answer The pit o2en contains hazards to the traveling cables, such
as _______, _______, and _______
Hose or escalator handrail - Answer The divider beams can be padded with _______ or _______
Wire mesh - Answer The complete area traveled by the cables can be protected with _______
Locate and repair - Answer If the old cables show serious abrasion, you must _______ the cause
Relocate - Answer On a replacement job you may have to _______ the car suspension point to
maintain correct loop size
Complete Verified Solu ons 2025.
One-half - Answer The Loop that is formed in the traveling cables at _______ the speed of the
car
Bracke ng a ached to the guide rail, the hoistway wall, or the building structure - Answer The
sta onary end of the traveling cable is fastened to _______, _______, or _______
Signal - Answer Each wire carries a specific electrical ________ between the car and the
machine room controls
Strain wire - Answer The steel core is called the _______
Reduce fric on and enhance flexibility - Answer Jute fibers are included to _______ and
_______
Torsional stress - Answer Before they are permanently installed, traveling cables should be hung
free in order to relieve _______
Spool - Answer On Lengths up to 100 feet _______ supports may be used
200 Feet - Answer On lengths over _______ the strain wire must be used for suspension
Junc on box - Answer At the permanent suspension point in the hoistway, slightly above the
center of travel, an electrical _______ may be installed
, 200 - Answer Cable grippers may be used to suspend up to _______ feet of traveling cable
Controller - Answer On a low-rise installa on, such as a hydraulic elevator, the traveling cables
may run to the _______
Fully compressed buffer - Answer On a high rise elevator with a deep pit, the reference point for
the lop in the traveling cable will be above the pit floor, where the car rests on the _______
Reel rollers, reel jacks, saw horses - Answer When the traveling cable is received on reels, the
reels can be set up on _______, _______, _______
Split cable gripper and swivel link - Answer When raising traveling cables with a hois ng line,
the line should be connected with a _______
Public safety - Answer On a cable replacement job, in an occupied building, the thing to keep
uppermost in your mind is _______
Brackets, switches, buffers - Answer The pit o2en contains hazards to the traveling cables, such
as _______, _______, and _______
Hose or escalator handrail - Answer The divider beams can be padded with _______ or _______
Wire mesh - Answer The complete area traveled by the cables can be protected with _______
Locate and repair - Answer If the old cables show serious abrasion, you must _______ the cause
Relocate - Answer On a replacement job you may have to _______ the car suspension point to
maintain correct loop size
