TATTOO MACHINE TEST COMPREHENSIVE EXAM
QUESTIONS WITH DETAILED VERIFIED AND 100%
ACCURATE ANSWERS BRAND NEW EXAM ALREADY
GRADED (A+ PASS)
Good daily maintenance of a coil device includes checking the
______________ with __________________. Ans✓✓✓gap of the rear
coil, canned air
The ___________ the gap between the front and rear coils, the more
powerful the vibration. Too _____________ of a gap may increase the
chances of the armature misaligning. Ans✓✓✓smaller, small
The greater distance energy has to travel, the more _________ and
____________ Ans✓✓✓heat and inefficiency
If you allow the front spring to hand over the rear armature bar, this will
likely Ans✓✓✓cause buzzing and severe vibration
A sharp edge or point on your contact screw will make it Ans✓✓✓wear
out faster
Every day, you should clean your contact area with Ans✓✓✓electronic
contact cleaner
Electricity moves (on the outside of/around/through/away from) metal
Ans✓✓✓on the outside of
, No matter the spring length, the screw should hit ____________
Ans✓✓✓at the end of the spring
The coil core should ideally be Ans✓✓✓perfectly smooth
What is an example of bad alignment (has to do with armature bar)?
Ans✓✓✓the armature bar not fully extending the length of the rear coil
True or False: A common reason for a machine to rattle is a straight side
arm. Ans✓✓✓False
True or False: A common reason for a machine to rattle is a twisted rear
spring. Ans✓✓✓True
True or False: a common reason for a machine to rattle is a angled
armature bar Ans✓✓✓true
True or False: a common reason for a machine to rattle is a poorly cut
coil top Ans✓✓✓true
______________ grommets are better than the alternatives.
Ans✓✓✓Rubber
QUESTIONS WITH DETAILED VERIFIED AND 100%
ACCURATE ANSWERS BRAND NEW EXAM ALREADY
GRADED (A+ PASS)
Good daily maintenance of a coil device includes checking the
______________ with __________________. Ans✓✓✓gap of the rear
coil, canned air
The ___________ the gap between the front and rear coils, the more
powerful the vibration. Too _____________ of a gap may increase the
chances of the armature misaligning. Ans✓✓✓smaller, small
The greater distance energy has to travel, the more _________ and
____________ Ans✓✓✓heat and inefficiency
If you allow the front spring to hand over the rear armature bar, this will
likely Ans✓✓✓cause buzzing and severe vibration
A sharp edge or point on your contact screw will make it Ans✓✓✓wear
out faster
Every day, you should clean your contact area with Ans✓✓✓electronic
contact cleaner
Electricity moves (on the outside of/around/through/away from) metal
Ans✓✓✓on the outside of
, No matter the spring length, the screw should hit ____________
Ans✓✓✓at the end of the spring
The coil core should ideally be Ans✓✓✓perfectly smooth
What is an example of bad alignment (has to do with armature bar)?
Ans✓✓✓the armature bar not fully extending the length of the rear coil
True or False: A common reason for a machine to rattle is a straight side
arm. Ans✓✓✓False
True or False: A common reason for a machine to rattle is a twisted rear
spring. Ans✓✓✓True
True or False: a common reason for a machine to rattle is a angled
armature bar Ans✓✓✓true
True or False: a common reason for a machine to rattle is a poorly cut
coil top Ans✓✓✓true
______________ grommets are better than the alternatives.
Ans✓✓✓Rubber
