1|Page
ASQ CQT EXAM ACTUAL QUESTIONS WITH
CORRECT SOLUTIONS
Inspection accuracy increases with
(A) reductions in defect rates
(B) repeated inspections
(C) additional product complexity
(D) order of sample selection -correct-answer-B repeated inspections
If a distribution is normal, with µ = 50 and σ = 15, what
percentage of data will be less than 30 ?
(A) 59.18%
(B) 40.82%
(C) 9.18%
(D) 1.33% -correct-answer-C 9.18%
The primary purpose of a first-article inspection is to
(A) teach the inspector how to check the part
(B) gather information on process capability
(C) verify that the sampling plan is appropriate
,2|Page
(D) ensure that the part conforms to specifications -correct-answer-D ensure that
the part conforms to specifications
The reduction or elimination of incoming inspection
stations should be considered only when
(A) evidence of supplier process control techniques is
provided for the material used
(B) evidence of a high defect rate is present in the
manufacturing operation
(C) the next process step will mask defects
(D) it is cost-prohibitive to the supplier to test the parts -correct-answer-A
evidence of supplier process control techniques is provided for the material used
A company is receiving an unusually high number of
returns from various customers. The first step in
investigating the problem would be to
(A) check the inspection records
(B) establish the correlation of the returns to shipments
(C) brainstorm the potential causes
(D) classify the returns by type and degree of seriousness -correct-answer-D
classify the returns by type and degree of seriousness
, 3|Page
A long-term corrective action plan is best described as a
(A) remedial action already taken
(B) temporary action on a current condition
(C) permanent action on an underlying cause
(D) containment action applied immediately -correct-answer-C permanent action
on an underlying cause
Which of the following is the first step for a technician to take when a
nonconforming product has been discovered?
(A) Contact quality management.
(B) Determine the product's fitness for use.
(C) Quarantine the product.
(D) Rework the product. -correct-answer-C Quarantine the product.
The weakest step in the corrective action process is
usually
(A) finding the problem
(B) containing the problem
(C) developing an action plan
(D) following up on the problem -correct-answer-D following up on the problem
ASQ CQT EXAM ACTUAL QUESTIONS WITH
CORRECT SOLUTIONS
Inspection accuracy increases with
(A) reductions in defect rates
(B) repeated inspections
(C) additional product complexity
(D) order of sample selection -correct-answer-B repeated inspections
If a distribution is normal, with µ = 50 and σ = 15, what
percentage of data will be less than 30 ?
(A) 59.18%
(B) 40.82%
(C) 9.18%
(D) 1.33% -correct-answer-C 9.18%
The primary purpose of a first-article inspection is to
(A) teach the inspector how to check the part
(B) gather information on process capability
(C) verify that the sampling plan is appropriate
,2|Page
(D) ensure that the part conforms to specifications -correct-answer-D ensure that
the part conforms to specifications
The reduction or elimination of incoming inspection
stations should be considered only when
(A) evidence of supplier process control techniques is
provided for the material used
(B) evidence of a high defect rate is present in the
manufacturing operation
(C) the next process step will mask defects
(D) it is cost-prohibitive to the supplier to test the parts -correct-answer-A
evidence of supplier process control techniques is provided for the material used
A company is receiving an unusually high number of
returns from various customers. The first step in
investigating the problem would be to
(A) check the inspection records
(B) establish the correlation of the returns to shipments
(C) brainstorm the potential causes
(D) classify the returns by type and degree of seriousness -correct-answer-D
classify the returns by type and degree of seriousness
, 3|Page
A long-term corrective action plan is best described as a
(A) remedial action already taken
(B) temporary action on a current condition
(C) permanent action on an underlying cause
(D) containment action applied immediately -correct-answer-C permanent action
on an underlying cause
Which of the following is the first step for a technician to take when a
nonconforming product has been discovered?
(A) Contact quality management.
(B) Determine the product's fitness for use.
(C) Quarantine the product.
(D) Rework the product. -correct-answer-C Quarantine the product.
The weakest step in the corrective action process is
usually
(A) finding the problem
(B) containing the problem
(C) developing an action plan
(D) following up on the problem -correct-answer-D following up on the problem
