Dante Level 1 EXAM 2025/2026 ACTUAL COMPLETE REAL EXAM
QUESTIONS AND CORRECT ANSWERS ( VERIFIED ANSWERS)
ALREADY GRADED A+ /2025 BRAND NEW EXAM!!
What are the steps to delete a subscription in Dante Controller?
- ANSWER--Open both transmitter and receiver to expose
channels
-Click green checkmark at intersection of channels you wish to
unsubscribe
-Wait for green checkmark to disappear
How are device names used in Dante? - ANSWER-
Subscriptions are made from name to name
What is a LAN? - ANSWER-A computer network that
interconnects computers using a common range of IP
addresses
What sample rates are supported by Dante? - ANSWER-Dante
supports most common sample rates, from 44.1kHz up to
192kHz
What is latency? - ANSWER-Latency is the audio signal delay in
any audio system.
,When should fiber be used for an Ethernet connection? -
ANSWER-When runs over 100 meters are required.
Do Dante devices require special IP configuration? - ANSWER-
No, all commonly supported IP address methods are supported
Does a Dante network require special configuration for
clocking? - ANSWER-No. A Clock Master is always
automatically elected by Dante
Dante transmitters are sources. Dante receivers are -------- -
ANSWER-Destinations
The easiest way to get IP addresses for a functional stand-
alone Dante network is for all devices and computers to: -
ANSWER-use the "obtain an IP Address Automatically" setting
Audio sent over a Dante network is: - ANSWER-uncompressed,
bit-perfect
What does the Dante Clock Master do? - ANSWER-Provides
synchronization for all Dante devices on the network
,Which of the following are diagnostic features of Dante
Controller? (check all that apply) - ANSWER--Latency
monitoring
-Clock monitoring
Approximately how much bandwidth is consumed by 64
channels of audio @ 48kHz/24 bit-depth, excluding network
overhead? - ANSWER-74mbits/sec
How does Dante interact with Energy Efficient Ethernet (EEE)
switches? - ANSWER-EEE switches are not recommended for
use with Dante
Where do Dante settings reside? - ANSWER-On individual
Dante devices
Does Dante require special network cabling? - ANSWER-
Regular CAT5E or CAT6 Ethernet cable is recommended
Dante uses ------- switches - ANSWER-Standard
What are the steps to create a subscription in Dante Controller?
- ANSWER--Open the transmitter and receiver to expose
channels of each
, -Click at the intersection of the two channels you wish to
connect
-Wait for green check mark to appear
Dante works best with ------ switches - ANSWER-gigabit
As sample rate is increased on a device, what other property is
usually changed? - ANSWER-Channel count is reduced
If Dante Controller is quit while audio is flowing on a Dante
network, what happens? - ANSWER-Nothing. Dante Controller
is not required to be present for a Dante network to work.
If a network is only used for Dante and has only one network
switch, then: - ANSWER-The network does not require a
managed switch
Is there any advantage to using automatic IP addressing on a
Dante network? - ANSWER-Yes. Automatic addressing ensures
that devices create a working LAN.
Does Dante support MIDI? - ANSWER-No. Dante only transports
audio data, and does not interfere with MIDI.
QUESTIONS AND CORRECT ANSWERS ( VERIFIED ANSWERS)
ALREADY GRADED A+ /2025 BRAND NEW EXAM!!
What are the steps to delete a subscription in Dante Controller?
- ANSWER--Open both transmitter and receiver to expose
channels
-Click green checkmark at intersection of channels you wish to
unsubscribe
-Wait for green checkmark to disappear
How are device names used in Dante? - ANSWER-
Subscriptions are made from name to name
What is a LAN? - ANSWER-A computer network that
interconnects computers using a common range of IP
addresses
What sample rates are supported by Dante? - ANSWER-Dante
supports most common sample rates, from 44.1kHz up to
192kHz
What is latency? - ANSWER-Latency is the audio signal delay in
any audio system.
,When should fiber be used for an Ethernet connection? -
ANSWER-When runs over 100 meters are required.
Do Dante devices require special IP configuration? - ANSWER-
No, all commonly supported IP address methods are supported
Does a Dante network require special configuration for
clocking? - ANSWER-No. A Clock Master is always
automatically elected by Dante
Dante transmitters are sources. Dante receivers are -------- -
ANSWER-Destinations
The easiest way to get IP addresses for a functional stand-
alone Dante network is for all devices and computers to: -
ANSWER-use the "obtain an IP Address Automatically" setting
Audio sent over a Dante network is: - ANSWER-uncompressed,
bit-perfect
What does the Dante Clock Master do? - ANSWER-Provides
synchronization for all Dante devices on the network
,Which of the following are diagnostic features of Dante
Controller? (check all that apply) - ANSWER--Latency
monitoring
-Clock monitoring
Approximately how much bandwidth is consumed by 64
channels of audio @ 48kHz/24 bit-depth, excluding network
overhead? - ANSWER-74mbits/sec
How does Dante interact with Energy Efficient Ethernet (EEE)
switches? - ANSWER-EEE switches are not recommended for
use with Dante
Where do Dante settings reside? - ANSWER-On individual
Dante devices
Does Dante require special network cabling? - ANSWER-
Regular CAT5E or CAT6 Ethernet cable is recommended
Dante uses ------- switches - ANSWER-Standard
What are the steps to create a subscription in Dante Controller?
- ANSWER--Open the transmitter and receiver to expose
channels of each
, -Click at the intersection of the two channels you wish to
connect
-Wait for green check mark to appear
Dante works best with ------ switches - ANSWER-gigabit
As sample rate is increased on a device, what other property is
usually changed? - ANSWER-Channel count is reduced
If Dante Controller is quit while audio is flowing on a Dante
network, what happens? - ANSWER-Nothing. Dante Controller
is not required to be present for a Dante network to work.
If a network is only used for Dante and has only one network
switch, then: - ANSWER-The network does not require a
managed switch
Is there any advantage to using automatic IP addressing on a
Dante network? - ANSWER-Yes. Automatic addressing ensures
that devices create a working LAN.
Does Dante support MIDI? - ANSWER-No. Dante only transports
audio data, and does not interfere with MIDI.
