TELEHANDLER STUDY GUIDE EXAM 2025 QUESTIONS WITH 100% PASSED
SOLUTIONS!!
Trained, Authorized - CORRECT ANSWER-Only _________ and ____________
persons must be permitted to operate a telehandler
Employer - CORRECT ANSWER-The ___________ must verify that the following has
been covered as part of operator's training
Inside - CORRECT ANSWER-The operator's manual should always be located
_______ the operator's cab.
Class 7 - CORRECT ANSWER-Telehandlers are classified as ________ Variable Reach
Rough Terrain Forklifts in the USA and Canada
Evaluation, 3 - CORRECT ANSWER-An _______________________ of each powered
industrial truck operator's performance shall be conducted at least once every
_____________years.
Center of Gravity - CORRECT ANSWER-is the point on an object at which all of the
object's weight is concentrated. For symmetrical loads, the center of gravity is at the
middle of the load.
, Counterweight - CORRECT ANSWER-is the weight that is built into the truck's basic
structure and is used to offset the load's weight and to maximize the vehicle's
resistance to tipping over.
Fulcrum - CORRECT ANSWER-is the truck's axis of rotation when it tips over.
Grade - CORRECT ANSWER-is the slope of a surface, which is usually measured as
the number of feet of rise or fall over a hundred foot horizontal distance (the slope is
expressed as a percent).
Lateral Stability - CORRECT ANSWER-is a truck's resistance to overturning sideways.
Line of action - CORRECT ANSWER-is an imaginary vertical line through an object's
center of gravity.
Load center - CORRECT ANSWER-is the horizontal distance from the load's edge (or
the fork's or other attachment's vertical face) to the line of action through the load's
center of gravity.
Longitudinal stability - CORRECT ANSWER-is the truck's resistance to overturning
forward or rearward.
Moment - CORRECT ANSWER-is the product of the object's weight times the distance
from a fixed point (usually the fulcrum). In the case of a powered industrial truck, the
distance is measured from the point at which the truck will tip over to the object's line of
action. The
distance is always measured perpendicular to the line of action.
Track - CORRECT ANSWER-is the distance between the wheels on the same axle of
the truck.
SOLUTIONS!!
Trained, Authorized - CORRECT ANSWER-Only _________ and ____________
persons must be permitted to operate a telehandler
Employer - CORRECT ANSWER-The ___________ must verify that the following has
been covered as part of operator's training
Inside - CORRECT ANSWER-The operator's manual should always be located
_______ the operator's cab.
Class 7 - CORRECT ANSWER-Telehandlers are classified as ________ Variable Reach
Rough Terrain Forklifts in the USA and Canada
Evaluation, 3 - CORRECT ANSWER-An _______________________ of each powered
industrial truck operator's performance shall be conducted at least once every
_____________years.
Center of Gravity - CORRECT ANSWER-is the point on an object at which all of the
object's weight is concentrated. For symmetrical loads, the center of gravity is at the
middle of the load.
, Counterweight - CORRECT ANSWER-is the weight that is built into the truck's basic
structure and is used to offset the load's weight and to maximize the vehicle's
resistance to tipping over.
Fulcrum - CORRECT ANSWER-is the truck's axis of rotation when it tips over.
Grade - CORRECT ANSWER-is the slope of a surface, which is usually measured as
the number of feet of rise or fall over a hundred foot horizontal distance (the slope is
expressed as a percent).
Lateral Stability - CORRECT ANSWER-is a truck's resistance to overturning sideways.
Line of action - CORRECT ANSWER-is an imaginary vertical line through an object's
center of gravity.
Load center - CORRECT ANSWER-is the horizontal distance from the load's edge (or
the fork's or other attachment's vertical face) to the line of action through the load's
center of gravity.
Longitudinal stability - CORRECT ANSWER-is the truck's resistance to overturning
forward or rearward.
Moment - CORRECT ANSWER-is the product of the object's weight times the distance
from a fixed point (usually the fulcrum). In the case of a powered industrial truck, the
distance is measured from the point at which the truck will tip over to the object's line of
action. The
distance is always measured perpendicular to the line of action.
Track - CORRECT ANSWER-is the distance between the wheels on the same axle of
the truck.
