CIRO CRO Chief Compliance Officer Exam Practice Guide
2024-2025
1. What is NOT mechanical integrity C. Permit Process
A. Housekeeping
B. Inspections / Tests
C. Permit Process
D. Preventative and Predictive
2. What is the common acronym for best practices B. RAGAGEP
A. IIAR
B. RAGAGEP
C. ASHRAE
D. ASME
3. What is CUI A. Corrosion under insula-
A. Corrosion under insulation tion
B. Compressor under isolation
C. Condenser under isolation
D. None of the above
4. What is CUPL A. Corrosion under pipe
A. Corrosion under pipe label label
B. Compressor under isolation and locked
C. Condenser under isolation and locked
D. None of the above
5. How much pipe loss is allowed by IIAR before they B. 10%
recommend subjective analysis
A. 5%
B. 10%
C. 15%
D. 20%
6. When taking an up-charge of ammonia, what is the B. 500PPM
most water concentration that should be in the am-
, CIRO CRO Chief Compliance Officer Exam Practice Guide
2024-2025
monia to be called anhydrous or refrigeration grade
ammonia
A. 100PPM
B. 500PPM
C. 1,000PPM
D. 5,000PPM
7. When water increases in concentration in the ammo- A. Rise compared to
SAT
nia it will cause many undesirable conditions; what will charts
happen to SAT temperature?
A. Rise compared to SAT charts
B. Lower compared to SAT charts
C. Stay the same
D. Depends on the pressure, sometimes rises and
sometimes lowers based upon SAT charts
8. What is NOT a non-destructive test (NDT) technique D. Phychrometric
used in mechanical integrity inspections
A. Infrared
B. Ultrasonic
C. Radiographic
D. Phychrometric
9. Which one below is NOT a factor of heat transfer B. Density of material
A. Temperature difference
B. Density of material
C. Thermal conductivity
D. Surface area
10. Thermal conductivity also known as 'K' value is A. A scientific measure-
A. A scientific measurement to the number of BTUs ment to the number of
that will pass in one hour, through a material 1" thick, BTUs that will pass in one
, CIRO CRO Chief Compliance Officer Exam Practice Guide
2024-2025
with an area of 1ft2, if the temperature difference from hour, through a material 1"
2024-2025
1. What is NOT mechanical integrity C. Permit Process
A. Housekeeping
B. Inspections / Tests
C. Permit Process
D. Preventative and Predictive
2. What is the common acronym for best practices B. RAGAGEP
A. IIAR
B. RAGAGEP
C. ASHRAE
D. ASME
3. What is CUI A. Corrosion under insula-
A. Corrosion under insulation tion
B. Compressor under isolation
C. Condenser under isolation
D. None of the above
4. What is CUPL A. Corrosion under pipe
A. Corrosion under pipe label label
B. Compressor under isolation and locked
C. Condenser under isolation and locked
D. None of the above
5. How much pipe loss is allowed by IIAR before they B. 10%
recommend subjective analysis
A. 5%
B. 10%
C. 15%
D. 20%
6. When taking an up-charge of ammonia, what is the B. 500PPM
most water concentration that should be in the am-
, CIRO CRO Chief Compliance Officer Exam Practice Guide
2024-2025
monia to be called anhydrous or refrigeration grade
ammonia
A. 100PPM
B. 500PPM
C. 1,000PPM
D. 5,000PPM
7. When water increases in concentration in the ammo- A. Rise compared to
SAT
nia it will cause many undesirable conditions; what will charts
happen to SAT temperature?
A. Rise compared to SAT charts
B. Lower compared to SAT charts
C. Stay the same
D. Depends on the pressure, sometimes rises and
sometimes lowers based upon SAT charts
8. What is NOT a non-destructive test (NDT) technique D. Phychrometric
used in mechanical integrity inspections
A. Infrared
B. Ultrasonic
C. Radiographic
D. Phychrometric
9. Which one below is NOT a factor of heat transfer B. Density of material
A. Temperature difference
B. Density of material
C. Thermal conductivity
D. Surface area
10. Thermal conductivity also known as 'K' value is A. A scientific measure-
A. A scientific measurement to the number of BTUs ment to the number of
that will pass in one hour, through a material 1" thick, BTUs that will pass in one
, CIRO CRO Chief Compliance Officer Exam Practice Guide
2024-2025
with an area of 1ft2, if the temperature difference from hour, through a material 1"
