• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 2 out of 6 pages
Other

Module 9: Ymca Submax Test Protocol| Latest 2025 Updated Solution

Document preview thumbnail
Preview 2 out of 6 pages

MODULE 9: YMCA SUBMAX TEST PROTOCOL| LATEST 2025 UPDATED SOLUTION Objective of the test The objective of the YMCA submaximal cycle test is to obtain and plot two steady-state* heart rate values between 110 bpm and the 85% of age predicted maximum heart rate. To attain this objective, a person may need to cycle for up to four stages. *average of the last two minutes during each stage Measurements during the test During the test, we assess and record the following on a data sheet: • o Heart rate: every minute (during the last 15s of the minute) o Blood pressure: once every stage in the third minute of the stage o RPE: once every stage in the third minute of the stage. Each Stage lasts at least 3 minutes with the resistance changing after the first stage based on the whether the participant has achieved "Steady-state" Steady-State Definition How do you know if the heart rate is at steady state? Steady state is determined by two heart rates being ≤ 5 beats per minute apart. Note that we measure heart rate every minute during the YMCA submax test. At a minimum, a stage must be 3min long. So, if heart rate in the 2nd and 3rd minutes is within 5 bpm, that would imply steady state. However, if the difference is 5bpm, you would need to extend the stage by 1 more minute (at least). To establish the line of best fit on the graph, at least two HR data points are needed, ideally between 110bpm and 85% of age predicted maximum heart rate. • o If difference between minute 2 and minute 3 HR = 5 bpm in Stage 1, use the appropriate Stage 2 resistance based on the chart below and continue to use the same column for each subsequent stage. o If difference between minute 2 and minute 3 HR 5 bpm, continue at the same stage for 1 more minute. Only move to next stage after steady state HR is established [i.e. = 5bpm difference between HR for last 2 minutes of a stage]. Average the last two heart rates in each stage before you plot the data. Example flowchart of how to run a test

Content preview

MODULE 9: YMCA SUBMAX TEST PROTOCOL| LATEST 2025
UPDATED SOLUTION

Objective of the test
The objective of the YMCA submaximal cycle test is to obtain and plot two steady-
state* heart rate values between 110 bpm and the 85% of age predicted maximum
heart rate. To attain this objective, a person may need to cycle for up to four stages.
*average of the last two minutes during each stage

Measurements during the test
During the test, we assess and record the following on a data sheet:
•
o Heart rate: every minute (during the last 15s of the minute)
o Blood pressure: once every stage in the third minute of the stage
o RPE: once every stage in the third minute of the stage.




Each Stage lasts at least 3 minutes with the resistance changing after the first stage
based on the whether the participant has achieved "Steady-state"

Steady-State Definition
How do you know if the heart rate is at steady state? Steady state is determined by
two heart rates being ≤ 5 beats per minute apart. Note that we measure heart rate
every minute during the YMCA submax test. At a minimum, a stage must be 3min
long. So, if heart rate in the 2nd and 3rd minutes is within 5 bpm, that would imply
steady state. However, if the difference is > 5bpm, you would need to extend the stage
by 1 more minute (at least). To establish the line of best fit on the graph, at least two HR
data points are needed, ideally between 110bpm and 85% of age predicted maximum
heart rate.
•


https://www.stuvia.com/user/Mboffin

, o If difference between minute 2 and minute 3 HR <= 5 bpm in Stage
1, use the appropriate Stage 2 resistance based on the chart below
and continue to use the same column for each subsequent stage.
o If difference between minute 2 and minute 3 HR > 5 bpm, continue
at the same stage for 1 more minute. Only move to next stage after
steady state HR is established [i.e. <= 5bpm difference between
HR for last 2 minutes of a stage]. Average the last two heart
rates in each stage before you plot the data.




Example flowchart of how to run a test




https://www.stuvia.com/user/Mboffin

Document information

Uploaded on
July 30, 2025
Number of pages
6
Written in
2024/2025
Type
Other
Person
Unknown
$17.49

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
MBOFFIN
3.7
(140)
Sold
788
Followers
218
Items
5732
Last sold
19 hours ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions