FDOT ASPHALT PAVING LEVEL 1 EXAM
WITH CORRECT ACTUAL QUESTIONS AND
CORRECTLY WELL DEFINED ANSWERS
LATEST ALREADY GRADED A+ 2025 - 2026
Tack used at night - ANSWERS-PG 52-28 which is multiplied the specification
rate by 0.6 to get your new target application rate.
Heated between 250 and 300°F
Tack allowed tolerance - ANSWERS-+-0.01 gal/syd
Base, Structural, or dense graded friction - ANSWERS-0.03 minimum gal/syd
on new constructed
0.06 gal/Syd milled surface
0.08 gal/Syd concrete
Open Graded Friction Course - ANSWERS-0.05 gal/Syd newly constructed
0.07 gal/Syd milled
, Perform the straight edge where in the road - ANSWERS-In the outside wheel
path
Straightedge and joints - ANSWERS-Use the manual and place 1 inch over the
joint and measure
Allow 3/8 deficiency
Straight Edge is the - ANSWERS-Measurement of Pavement smoothness with
a 15 foot 4.573 m rolling straightedge
Straight Edge is used to - ANSWERS-identify problems
Random sampling - ANSWERS-Are random numbers generated usually by a
VT for cores to be extracted from the roadway
How often should you calibrate a Straight edge - ANSWERS-Calibrate at the
start of each working period
Using the manual straight edge you find what kind of spot to place the rolling
straightedge? - ANSWERS-Locate a flat area with the manual straightedge and
place the rolling straightedge next to the manual straightedge and the gauge
should read 0
The 3/16 and the 3/8 shims go under which wheels during calibration -
ANSWERS-The outside wheels to measure the low and the center to measure
the high. Gauge should read 3/16 on the 3/16 shim and vice versa for the 3/8
shims. Make sure the center wheel moves up and down freely.
WITH CORRECT ACTUAL QUESTIONS AND
CORRECTLY WELL DEFINED ANSWERS
LATEST ALREADY GRADED A+ 2025 - 2026
Tack used at night - ANSWERS-PG 52-28 which is multiplied the specification
rate by 0.6 to get your new target application rate.
Heated between 250 and 300°F
Tack allowed tolerance - ANSWERS-+-0.01 gal/syd
Base, Structural, or dense graded friction - ANSWERS-0.03 minimum gal/syd
on new constructed
0.06 gal/Syd milled surface
0.08 gal/Syd concrete
Open Graded Friction Course - ANSWERS-0.05 gal/Syd newly constructed
0.07 gal/Syd milled
, Perform the straight edge where in the road - ANSWERS-In the outside wheel
path
Straightedge and joints - ANSWERS-Use the manual and place 1 inch over the
joint and measure
Allow 3/8 deficiency
Straight Edge is the - ANSWERS-Measurement of Pavement smoothness with
a 15 foot 4.573 m rolling straightedge
Straight Edge is used to - ANSWERS-identify problems
Random sampling - ANSWERS-Are random numbers generated usually by a
VT for cores to be extracted from the roadway
How often should you calibrate a Straight edge - ANSWERS-Calibrate at the
start of each working period
Using the manual straight edge you find what kind of spot to place the rolling
straightedge? - ANSWERS-Locate a flat area with the manual straightedge and
place the rolling straightedge next to the manual straightedge and the gauge
should read 0
The 3/16 and the 3/8 shims go under which wheels during calibration -
ANSWERS-The outside wheels to measure the low and the center to measure
the high. Gauge should read 3/16 on the 3/16 shim and vice versa for the 3/8
shims. Make sure the center wheel moves up and down freely.
