OSHA 510 Test prep questions
Accident prevention programs require CP inspections how often - ANS - Frequent
\All supported scaffold shall be restrained by tying, tying or bracing at what height - ANS - 4 to 1
ratio
\Damaged trench she'll she'll be removed from service by a competent person and evaluated
and approved for continuous use by whom - ANS - Professional engineer
\Demolition operations require an enclosed shoot for material disposal when - ANS - Above or
equal to 45° angle
\Electrical equipment requires grounding against accidental contact over how many volts - ANS
- 50 V
\I'll hand and power tools must be maintained and what condition - ANS - Good operating
conditions and free from recognize hazards and guarded
Masonry wall is a required breeze that what Heights? - ANS - 8 feet
\OSHA act section 1 contains white key statement - ANS - Protecting workers
\Removal of equipment roll over protective structure she'll only be remounted when - ANS -
When equal or better bolts are required for her original mounting
\Sub part H requires already equipment to be inspected when - ANS - Prior to each shift and as
necessary before each use
\What actions were decorating employer fail to take which would likely result in a citation under
the multiemployer citation policy - ANS - Failed to inform hazards
\What are some of results of workplace injuries and illnesses - ANS - Last time, days away,
lower morale, increased cost
\What are the four main parts of an OSHA inspection - ANS - Credentials, opening, walk
around, and closing
\What does the OSHA recordkeeping incident rate and calculation include - ANS - Number of
employees times 200,000 divided by total hours worked
\What health hazard are you likely to encounter when engaged in Bridge repair, residential
renovation, demolition, and salvaging work - ANS - Lead, asbestos, and silica
\What is the definition of a qualified person - ANS - Ability to demonstrate knowledge and has a
recognized agree
\What is the hierarchy of controls for controlling chemical exposure - ANS - Elimination,
substitution, engineering, administrative, personal protective equipment
\What is the maximum allowed for distance for a personal fall arrest system to ensure the
worker does not hit the ground and or strike a lower level object - ANS - 6 feet
\What is the minimum clearance between overhead sprinklers deflectors and material store
beneath them - ANS - 36 inches
\What is the minimum clearance between the side rails of a portable ladder - ANS - 11.5 ft
\What must an employer do if they identify a circular saw with a damaged cord and or missing
blade guard - ANS - Tag and removed from service
Accident prevention programs require CP inspections how often - ANS - Frequent
\All supported scaffold shall be restrained by tying, tying or bracing at what height - ANS - 4 to 1
ratio
\Damaged trench she'll she'll be removed from service by a competent person and evaluated
and approved for continuous use by whom - ANS - Professional engineer
\Demolition operations require an enclosed shoot for material disposal when - ANS - Above or
equal to 45° angle
\Electrical equipment requires grounding against accidental contact over how many volts - ANS
- 50 V
\I'll hand and power tools must be maintained and what condition - ANS - Good operating
conditions and free from recognize hazards and guarded
Masonry wall is a required breeze that what Heights? - ANS - 8 feet
\OSHA act section 1 contains white key statement - ANS - Protecting workers
\Removal of equipment roll over protective structure she'll only be remounted when - ANS -
When equal or better bolts are required for her original mounting
\Sub part H requires already equipment to be inspected when - ANS - Prior to each shift and as
necessary before each use
\What actions were decorating employer fail to take which would likely result in a citation under
the multiemployer citation policy - ANS - Failed to inform hazards
\What are some of results of workplace injuries and illnesses - ANS - Last time, days away,
lower morale, increased cost
\What are the four main parts of an OSHA inspection - ANS - Credentials, opening, walk
around, and closing
\What does the OSHA recordkeeping incident rate and calculation include - ANS - Number of
employees times 200,000 divided by total hours worked
\What health hazard are you likely to encounter when engaged in Bridge repair, residential
renovation, demolition, and salvaging work - ANS - Lead, asbestos, and silica
\What is the definition of a qualified person - ANS - Ability to demonstrate knowledge and has a
recognized agree
\What is the hierarchy of controls for controlling chemical exposure - ANS - Elimination,
substitution, engineering, administrative, personal protective equipment
\What is the maximum allowed for distance for a personal fall arrest system to ensure the
worker does not hit the ground and or strike a lower level object - ANS - 6 feet
\What is the minimum clearance between overhead sprinklers deflectors and material store
beneath them - ANS - 36 inches
\What is the minimum clearance between the side rails of a portable ladder - ANS - 11.5 ft
\What must an employer do if they identify a circular saw with a damaged cord and or missing
blade guard - ANS - Tag and removed from service
