CM 2215 OSHA 510 Study Guide
0 - ANS - The material used in rollover protection structures must have the capability of
performing at ___ degrees F
\10 - ANS - When mechanical equipment is being used perpendicular to the roof edge, the
warning lines cannot be closer than ___ feet.
\100 - ANS - In OSHA Record keeping, an incidence rate is the number of recordable injuries or
illness per ___ full-time workers.
\100 - ANS - The maximum travel distance from any point of the protected area to the nearest
fire extinguisher shall not exceed ___ feet
\11(c) - ANS - The right of the worker to seek safety and health on the job site without fear of
punishment can be found in Section___ of the OSH Act
\12 - ANS - Type A soil can be sloped at 1/2:1 ratio if the excavation is open for less than 24
hours and is less than ___ feet deep.
\134 - ANS - Respirators used in the construction industry are covered under OSHA standard
1910.___
\178 - ANS - The operator training requirements for rough terrain trucks used in the construction
industry are covered under OSHA standard 1910.___ Powered Industrial Trucks
\20 and 30, 48 - ANS - Cross bracing on a scaffold is only acceptable as a mid-rail when the
crossing point of the two braces is between ___ and ___ inches above the work platform and
end points are less than ___ inches apart.
\3 - ANS - On temporary stairs, handrails (to provide adequate handholds for employees
grasping to prevent falling) shall have a minimum clearance of ___ inches between the
handrails and walls
\3.5 - ANS - When stopping a fall, a personal fall arrest system, shall bring an employee to a
complete stop and limit the maximum deceleration distance to ___ feet.
\30 - ANS - A controlled decking zone can only be used as fall protection up to a maximum
height of ___ feet
\4 - ANS - Except for extra-heavy-duty metal or plastic portable ladders, all portable ladders
must support ___ times the maximum intended load.
\4 - ANS - When masonry walls are being constructed, a limited access zone at least the height
of the wall plus ___ feet tall shall be established on the side of the wall without scaffolding.
\42 - ANS - According to 1926.502(b)(1), the top rail of a guardrail system must be a height of
___ inches +/- 3 inches above the walking/working level.
\45 - ANS - A material chute used during demolition operations bust be enclosed when its angle
is equal to or greater than ___ degrees above the horizontal.
\50 - ANS - ___ volts or greater is the maximum voltage before guarding is required against
accidental contact by cabinets, other forms of enclosure, or by location in a room or enclosure
accessible only to qualified persons (electricians).
\6 - ANS - Personal fall arrest systems, when stopping a fall, shall be rigged such that an
employee cannot free fall more than ___ feet or contact any lower level.
\8 - ANS - ___ ft is the trigger height when masonry walls must be braced.
0 - ANS - The material used in rollover protection structures must have the capability of
performing at ___ degrees F
\10 - ANS - When mechanical equipment is being used perpendicular to the roof edge, the
warning lines cannot be closer than ___ feet.
\100 - ANS - In OSHA Record keeping, an incidence rate is the number of recordable injuries or
illness per ___ full-time workers.
\100 - ANS - The maximum travel distance from any point of the protected area to the nearest
fire extinguisher shall not exceed ___ feet
\11(c) - ANS - The right of the worker to seek safety and health on the job site without fear of
punishment can be found in Section___ of the OSH Act
\12 - ANS - Type A soil can be sloped at 1/2:1 ratio if the excavation is open for less than 24
hours and is less than ___ feet deep.
\134 - ANS - Respirators used in the construction industry are covered under OSHA standard
1910.___
\178 - ANS - The operator training requirements for rough terrain trucks used in the construction
industry are covered under OSHA standard 1910.___ Powered Industrial Trucks
\20 and 30, 48 - ANS - Cross bracing on a scaffold is only acceptable as a mid-rail when the
crossing point of the two braces is between ___ and ___ inches above the work platform and
end points are less than ___ inches apart.
\3 - ANS - On temporary stairs, handrails (to provide adequate handholds for employees
grasping to prevent falling) shall have a minimum clearance of ___ inches between the
handrails and walls
\3.5 - ANS - When stopping a fall, a personal fall arrest system, shall bring an employee to a
complete stop and limit the maximum deceleration distance to ___ feet.
\30 - ANS - A controlled decking zone can only be used as fall protection up to a maximum
height of ___ feet
\4 - ANS - Except for extra-heavy-duty metal or plastic portable ladders, all portable ladders
must support ___ times the maximum intended load.
\4 - ANS - When masonry walls are being constructed, a limited access zone at least the height
of the wall plus ___ feet tall shall be established on the side of the wall without scaffolding.
\42 - ANS - According to 1926.502(b)(1), the top rail of a guardrail system must be a height of
___ inches +/- 3 inches above the walking/working level.
\45 - ANS - A material chute used during demolition operations bust be enclosed when its angle
is equal to or greater than ___ degrees above the horizontal.
\50 - ANS - ___ volts or greater is the maximum voltage before guarding is required against
accidental contact by cabinets, other forms of enclosure, or by location in a room or enclosure
accessible only to qualified persons (electricians).
\6 - ANS - Personal fall arrest systems, when stopping a fall, shall be rigged such that an
employee cannot free fall more than ___ feet or contact any lower level.
\8 - ANS - ___ ft is the trigger height when masonry walls must be braced.
