NYS 17-71 INDEPENDENT GENERAL
ADJUSTER EXAM 2025/2026 WITH ACTUAL
CORRECT QUESTIONS AND VERIFIED
DETAILED ANSWERS |FREQUENTLY TESTED
QUESTIONS AND SOLUTIONS |ALREADY
GRADED A+|NEWEST|BRAND NEW
VERSION!!|GUARANTEED PASS
The _________ are typically welded to the floor pan, pillars, and quarter panels.
Rocker Panel
This type of brake is made up of a caliper, two brake pads, and a rotor.
Disc Brake
The _____ opens and closes valves.
Camshaft
In a _____ headlamp, the lamp housing, bulb, and lens are separate units allowing for
replacement of just the bulb.
Composite
______ are large strips of steel bolted together with fiberglass inbetween.
Leaf Springs
In the POI numbering system, what does number refers to damage "all over"?
19
In older cars, the ______ controls the timing and delivery of fuel into the engine.
Carburetor
1|Page
,In ______ fuel injection, each fuel injector is screwed into the engine head that extends directly
into each combustion chamber.
This system also uses a high pressure fuel pump with pressure higher than the combustion
chamber.
Direct
Radiator cooling fans move air through the radiator and ________.
A/C Condenser
Where is the heater core located?
Under the dashboard
A _____ is used in front-wheel drive and is basically a combination of a differential and
transmission.
Transaxle
_______ is when electrodes clamp two sheets of metal together.
Resistance Spot Welding (RSW)
________ are used to reduce friction and wear on gears.
Ball Bearings
In automatic transmissions, the _______ replaces the clutch.
Torque Converter
A ______ is hinged at the bottom.
Tailgate
_________ damage occurs when measurements from the center line are no longer equal.
Sway
The _________ is a detachable part of the unibody that supports the engine and transmission.
Subframe
A subframe is seen in which type of vehicle?
Unibody
2|Page
, This type of vehicle does not have a B-Pillar to support the roof.
Hardtop
When the clutch petal is pushed, the ______ separates from the spinning fly wheel to allow
gear change.
Clutch Disc/Plate
______ welding uses non-consumable wire electrode and shielding gas.
TIG
_________ allows exhaust gas to flow from the exhaust manifold to the intake manifold to be
burned again.
Exhaust Gas Recirculation (EGR)
Which of the following is a primary restraint system?
Seat Belts
What should you check first when searching for an electrical problem?
Fuses
Which of the following would be a moral hazard?
Intentionally lighting your car on fire
What is the continuing education requirement for Independent Adjusters.
There is none
When must you notify the Superintendent of an address change?
Within 30 days
If the Superintendent imposes 5 separate civil penalties against any one person within 5 years,
the Superintendent can impose an additional civil penalty against the person up to a maximum
of _______ for every 5 year period.
$50,000
If the Superintendent decides to suspend or revoke a license, the licensee must wait ____
before applying for a license again.
1 year
3|Page
ADJUSTER EXAM 2025/2026 WITH ACTUAL
CORRECT QUESTIONS AND VERIFIED
DETAILED ANSWERS |FREQUENTLY TESTED
QUESTIONS AND SOLUTIONS |ALREADY
GRADED A+|NEWEST|BRAND NEW
VERSION!!|GUARANTEED PASS
The _________ are typically welded to the floor pan, pillars, and quarter panels.
Rocker Panel
This type of brake is made up of a caliper, two brake pads, and a rotor.
Disc Brake
The _____ opens and closes valves.
Camshaft
In a _____ headlamp, the lamp housing, bulb, and lens are separate units allowing for
replacement of just the bulb.
Composite
______ are large strips of steel bolted together with fiberglass inbetween.
Leaf Springs
In the POI numbering system, what does number refers to damage "all over"?
19
In older cars, the ______ controls the timing and delivery of fuel into the engine.
Carburetor
1|Page
,In ______ fuel injection, each fuel injector is screwed into the engine head that extends directly
into each combustion chamber.
This system also uses a high pressure fuel pump with pressure higher than the combustion
chamber.
Direct
Radiator cooling fans move air through the radiator and ________.
A/C Condenser
Where is the heater core located?
Under the dashboard
A _____ is used in front-wheel drive and is basically a combination of a differential and
transmission.
Transaxle
_______ is when electrodes clamp two sheets of metal together.
Resistance Spot Welding (RSW)
________ are used to reduce friction and wear on gears.
Ball Bearings
In automatic transmissions, the _______ replaces the clutch.
Torque Converter
A ______ is hinged at the bottom.
Tailgate
_________ damage occurs when measurements from the center line are no longer equal.
Sway
The _________ is a detachable part of the unibody that supports the engine and transmission.
Subframe
A subframe is seen in which type of vehicle?
Unibody
2|Page
, This type of vehicle does not have a B-Pillar to support the roof.
Hardtop
When the clutch petal is pushed, the ______ separates from the spinning fly wheel to allow
gear change.
Clutch Disc/Plate
______ welding uses non-consumable wire electrode and shielding gas.
TIG
_________ allows exhaust gas to flow from the exhaust manifold to the intake manifold to be
burned again.
Exhaust Gas Recirculation (EGR)
Which of the following is a primary restraint system?
Seat Belts
What should you check first when searching for an electrical problem?
Fuses
Which of the following would be a moral hazard?
Intentionally lighting your car on fire
What is the continuing education requirement for Independent Adjusters.
There is none
When must you notify the Superintendent of an address change?
Within 30 days
If the Superintendent imposes 5 separate civil penalties against any one person within 5 years,
the Superintendent can impose an additional civil penalty against the person up to a maximum
of _______ for every 5 year period.
$50,000
If the Superintendent decides to suspend or revoke a license, the licensee must wait ____
before applying for a license again.
1 year
3|Page
