SIFT (Army Aviation Information)
Practice Test Questions and Answers
The typical structure of a helicopter is a ______ (fill in the blank) with a ____ (fill in the
blank) protruding upward out of it. - correct Answer-Fuselage (the body of the craft),
Mast.
The engine of the craft drives power upward through the ____ (fill in the blank) to the
rotor blades, which are controlled by the pilot. - correct Answer-Mast
This main rotor is used to generate ____ (fill in the blank). - correct Answer-Thrust.
____ (fill in the blank) is balanced by a second rotor, usually a tail rotor, which is
intended to account for the effects of ____ (fill in the blank). - correct Answer-Thrust,
Torque.
What are the two main types of aircraft? - correct Answer-Rotorcraft and Fixed Wing.
The main advantage of a helicopter over an airplane is its ability to takeoff ____ (fill in
the blank). It can also ____ (fill in the blank). This means helicopters can be used to
takeoff from and land in places that would be impossible for planes. They can also
perform tasks such as dropping cargo or troops into challenging positions. - correct
Answer-Vertically, Hover.
What are the different Helicopter types? - correct Answer-Single Main Rotor, Tandem
Rotor, and Coaxial Rotor.
This is the most common design for a helicopter- a ____ (fill in the blank) rotor
generating power, with a secondary rotor, such as a tail rotor, used to offset the effects
of torque. One disadvantage of this design is that some power is used for countering
____ (fill in the blank), rather than being used solely for lift. - correct Answer-A Single
Main Rotor, Torque.
This helicopter design features two main rotating blade sections: front and rear. Each
set of blades rotates counter to the other, meaning that torque is automatically offset.
There is no need for additional measures, such as a tail rotor, to deal with torque.
Because of this, all of the power from the engine can be used to lift. Consequently, ____
(fill in the blank) helicopters are some of the fastest and most powerful in existence. -
correct Answer-Tandem Rotor Helicopter.
, This type of helicopter features two sets of blades rotating above and beneath each
other. The two sets of blades are mounted to the same mast, but rotate in opposite
directions to each other. This has the advantage of reducing ____ (fill in the blank) and
allowing for greater cargo and passenger capacity as a result. - correct Answer-Coaxial
Rotor Helicopter, Payload.
____ (fill in the blank) is created by the engine, or engines, of the helicopter. It is
transferred into motion via the ____ (fill in the blank) and ____ (fill in the blank).
Sufficient ____ (fill in the blank) is needed to overcome the drag and the weight of the
helicopter and keep moving it forward. - correct Answer-Thrust, Mast and Rotors,
Thrust.
____ (fill in the blank) is a force which acts against thrust. In the case of helicopters,
drag is caused by the shape and size of the aircraft disrupting the flow of air as it
travels. There are several types of ____ (fill in the blank) which impact helicopters. -
correct Answer-Drag
What are the 4 different types of Drag? - correct Answer-Profile Drag, Induced Drag,
Parasite Drag, Total Drag.
____ (fill in the blank) is caused by the frictional resistance of helicopter blades passing
through the air. - correct Answer-Profile Drag.
What are the two subcomponents of Profile Drag? - correct Answer-Form Drag and Skin
Friction.
____ (fill in the blank) increases as the speed of the helicopter increases. - correct
Answer-Form Drag.
____ (fill in the blank) is caused by microscopic roughness of the helicopter blades. Any
roughness on the surface causes air to become trapped and drag to increase. - correct
Answer-Skin Friction.
____ (fill in the blank) is caused by airflow circulation around the blades creating
vortices. This type of drag increases when the helicopter is flying at lower speeds, and
decreases when it is flying at higher speeds. During low speed flight, ____ (fill in the
blank) is the main cause of drag for helicopters. - correct Answer-Induced Drag,
Induced Drag.
____ (fill in the blank) is the drag created by the helicopter components that are external
to the fuselage. For example, the landing gear, cowlings and doors can all create ____
(fill in the blank) drag. ____ (fill in the blank) drag slows down the speed of a helicopter
by opposing thrust. - correct Answer-Parasite Drag.
____ (fill in the blank) are achieved through manipulation of the collective. Moving the
collective manipulates the amount of lift, causing the helicopter to rise or fall as the pilot
desires. - correct Answer-Climbs and Descents
Practice Test Questions and Answers
The typical structure of a helicopter is a ______ (fill in the blank) with a ____ (fill in the
blank) protruding upward out of it. - correct Answer-Fuselage (the body of the craft),
Mast.
The engine of the craft drives power upward through the ____ (fill in the blank) to the
rotor blades, which are controlled by the pilot. - correct Answer-Mast
This main rotor is used to generate ____ (fill in the blank). - correct Answer-Thrust.
____ (fill in the blank) is balanced by a second rotor, usually a tail rotor, which is
intended to account for the effects of ____ (fill in the blank). - correct Answer-Thrust,
Torque.
What are the two main types of aircraft? - correct Answer-Rotorcraft and Fixed Wing.
The main advantage of a helicopter over an airplane is its ability to takeoff ____ (fill in
the blank). It can also ____ (fill in the blank). This means helicopters can be used to
takeoff from and land in places that would be impossible for planes. They can also
perform tasks such as dropping cargo or troops into challenging positions. - correct
Answer-Vertically, Hover.
What are the different Helicopter types? - correct Answer-Single Main Rotor, Tandem
Rotor, and Coaxial Rotor.
This is the most common design for a helicopter- a ____ (fill in the blank) rotor
generating power, with a secondary rotor, such as a tail rotor, used to offset the effects
of torque. One disadvantage of this design is that some power is used for countering
____ (fill in the blank), rather than being used solely for lift. - correct Answer-A Single
Main Rotor, Torque.
This helicopter design features two main rotating blade sections: front and rear. Each
set of blades rotates counter to the other, meaning that torque is automatically offset.
There is no need for additional measures, such as a tail rotor, to deal with torque.
Because of this, all of the power from the engine can be used to lift. Consequently, ____
(fill in the blank) helicopters are some of the fastest and most powerful in existence. -
correct Answer-Tandem Rotor Helicopter.
, This type of helicopter features two sets of blades rotating above and beneath each
other. The two sets of blades are mounted to the same mast, but rotate in opposite
directions to each other. This has the advantage of reducing ____ (fill in the blank) and
allowing for greater cargo and passenger capacity as a result. - correct Answer-Coaxial
Rotor Helicopter, Payload.
____ (fill in the blank) is created by the engine, or engines, of the helicopter. It is
transferred into motion via the ____ (fill in the blank) and ____ (fill in the blank).
Sufficient ____ (fill in the blank) is needed to overcome the drag and the weight of the
helicopter and keep moving it forward. - correct Answer-Thrust, Mast and Rotors,
Thrust.
____ (fill in the blank) is a force which acts against thrust. In the case of helicopters,
drag is caused by the shape and size of the aircraft disrupting the flow of air as it
travels. There are several types of ____ (fill in the blank) which impact helicopters. -
correct Answer-Drag
What are the 4 different types of Drag? - correct Answer-Profile Drag, Induced Drag,
Parasite Drag, Total Drag.
____ (fill in the blank) is caused by the frictional resistance of helicopter blades passing
through the air. - correct Answer-Profile Drag.
What are the two subcomponents of Profile Drag? - correct Answer-Form Drag and Skin
Friction.
____ (fill in the blank) increases as the speed of the helicopter increases. - correct
Answer-Form Drag.
____ (fill in the blank) is caused by microscopic roughness of the helicopter blades. Any
roughness on the surface causes air to become trapped and drag to increase. - correct
Answer-Skin Friction.
____ (fill in the blank) is caused by airflow circulation around the blades creating
vortices. This type of drag increases when the helicopter is flying at lower speeds, and
decreases when it is flying at higher speeds. During low speed flight, ____ (fill in the
blank) is the main cause of drag for helicopters. - correct Answer-Induced Drag,
Induced Drag.
____ (fill in the blank) is the drag created by the helicopter components that are external
to the fuselage. For example, the landing gear, cowlings and doors can all create ____
(fill in the blank) drag. ____ (fill in the blank) drag slows down the speed of a helicopter
by opposing thrust. - correct Answer-Parasite Drag.
____ (fill in the blank) are achieved through manipulation of the collective. Moving the
collective manipulates the amount of lift, causing the helicopter to rise or fall as the pilot
desires. - correct Answer-Climbs and Descents
