6/26/25, 11:47 AM Michigan State Brakes Certification
Michigan State Brakes Certification\\NEWEST
VERSION 2025-2026 \COMPLETE QUESTIONS AND
ACCURATE DETAILED ANSWERS \VERIFIED
SOLUTIONS ALREADY GRADED A+
The brakes of a car squeal Glazed brake pads
each time they are applied,
which of the following is
the LEAST likely source of
the noise?
Which of the following is a They provide better braking balance during hard stops
true statement about
proportioning valves?
A properly functioning load cause an increase in the hydraulic pressure during
sensing proportioning braking at the rear wheel cylinders when the vehicle is
valve will: loaded.
Why don't disc brake A certain amount of pressure is maintained by the metering valve
system usually need
adjustment?
The front brakes of a car Defective metering valve
equipped with disc brakes
in the front and drum brakes
in the rear, grab quickly as
light pressure is
applied to the brake pedal,
which of the following
could be the cause of the
problem?
The brake warning light on A problem in the hydraulic circuit
the dash stays on all the
time, which of the
following
/ 1/1
1
, 6/26/25, 11:47 AM Michigan State Brakes Certification
could be the cause of the
problem?
Which of the following Open wheel sensor circuit
would be the LEAST likely
cause for an intermittent
problem in an ABS
system?
The brake lights on a car do A burned out bulb.
not light when the brake
pedal is depressed, which of
the following is the LEAST
likely cause of the
problem?
Which of the following incorrect run-out on the car brake lathe
incorrect service
procedures could cause
brake pedal
pulsation?
What type of rotor surface A smooth, flat surface
provides the best braking
with new pads?
which of the following is a pump up the brake pedal, then hold it firm. if the pedal
quick way to slowly drops to the floor, the master cylinder may be
isolated a defective master
defective.
cylinder? There are no
external leaks in the
system.
A common cause of pedal NOT caused by improperly torqued wheels, damaged
pulsation during brake backing plates, or lubricated shims
application is:
the car is at reset. When dry backing plate contact surfaces
you slowly apply the brake
pedal you hear a squeaking
noise at the rear of the
vehicle. what could cause
this noise?
/ 2/1
1
Michigan State Brakes Certification\\NEWEST
VERSION 2025-2026 \COMPLETE QUESTIONS AND
ACCURATE DETAILED ANSWERS \VERIFIED
SOLUTIONS ALREADY GRADED A+
The brakes of a car squeal Glazed brake pads
each time they are applied,
which of the following is
the LEAST likely source of
the noise?
Which of the following is a They provide better braking balance during hard stops
true statement about
proportioning valves?
A properly functioning load cause an increase in the hydraulic pressure during
sensing proportioning braking at the rear wheel cylinders when the vehicle is
valve will: loaded.
Why don't disc brake A certain amount of pressure is maintained by the metering valve
system usually need
adjustment?
The front brakes of a car Defective metering valve
equipped with disc brakes
in the front and drum brakes
in the rear, grab quickly as
light pressure is
applied to the brake pedal,
which of the following
could be the cause of the
problem?
The brake warning light on A problem in the hydraulic circuit
the dash stays on all the
time, which of the
following
/ 1/1
1
, 6/26/25, 11:47 AM Michigan State Brakes Certification
could be the cause of the
problem?
Which of the following Open wheel sensor circuit
would be the LEAST likely
cause for an intermittent
problem in an ABS
system?
The brake lights on a car do A burned out bulb.
not light when the brake
pedal is depressed, which of
the following is the LEAST
likely cause of the
problem?
Which of the following incorrect run-out on the car brake lathe
incorrect service
procedures could cause
brake pedal
pulsation?
What type of rotor surface A smooth, flat surface
provides the best braking
with new pads?
which of the following is a pump up the brake pedal, then hold it firm. if the pedal
quick way to slowly drops to the floor, the master cylinder may be
isolated a defective master
defective.
cylinder? There are no
external leaks in the
system.
A common cause of pedal NOT caused by improperly torqued wheels, damaged
pulsation during brake backing plates, or lubricated shims
application is:
the car is at reset. When dry backing plate contact surfaces
you slowly apply the brake
pedal you hear a squeaking
noise at the rear of the
vehicle. what could cause
this noise?
/ 2/1
1
