NCCER MILLWRIGHT PRACTICE EXAM 2
If the seal was not properly aligned or
there is excessive wear in some bearing
unusual
or shaft,_______ wear tracks will be the
indicator
For removing hard to remove gasket
materials found on sealing surfaces, sharpened brass putty knife
______ is recommended
Apprenticeship training is_______ Conducted on the job
Charting alignment on a graph requires
a chart that is divided into thousandths of
an inch vertically for the indicator read- distance
ings and into whole inches horizontally
for the__________
The orthographic drawing may contain a
hidden
dashed or _______ line
In order to shoot through a test object
and project an image onto a detector or a
Radiation
sheet of film, radiography uses a source
of penetrating called _______
*scribe circles
Which of the following task would you not *transfer measurements
perform with dividers? *compare distances
<measure angles
The over speed trip device is actuated
when the turbine reaches a predeter-
10%
mined limit usually _________% above
normal full-load speed
Positive results in an offset measure-
ment mean that the MTBM is _____ or high
on the 3-o'clock side.
The coupling gap is set, and then the
offset misalignment
______ is measured
In a hydraulic system, movement de-
pressure
pends on_____
, NCCER MILLWRIGHT PRACTICE EXAM 2
Fractional dimensions are used on ob-
furniture or utility items
jects such as _______ or ______
If the cause of the problem is not
immediately understood, the process
elimination
of________is often the procedure of
choice
When applying sealant to the sealing
gland flanges, keep the sealant away
3/16
from the inside edges of the flange by at
least_______ inch
A stroboscope is triggered by a_______ Transducer
The pitch of threaded fasteners is mea-
thread
sured with a ________gauge
Liquid penetrant highlights flaws and re-
Surface cracks
veals________
A tool used to cut external threats on s
die
bolt or rod is called a ______
A bill of materials may include info on
_______ and other reference informa- special processes
tion
Engaged gears always have the same
surface speed
_____
Elevation of equipment is usually found
general arrangement
in the_____
Inspect the pulleys, rollers, and idlers for
Vibrations
unevenness or______
When cutting thin steel with Oxyfuel fuel
cutting equipment, hold the torch so that
15-20 degree angle
the tip is pointing in the direction the
torch is traveling at a _____ angle
Labby seals work BEST with materials
Grease.........
such as_____
Lubrication is the application of any sub-
Friction
stance that reduces________
If the seal was not properly aligned or
there is excessive wear in some bearing
unusual
or shaft,_______ wear tracks will be the
indicator
For removing hard to remove gasket
materials found on sealing surfaces, sharpened brass putty knife
______ is recommended
Apprenticeship training is_______ Conducted on the job
Charting alignment on a graph requires
a chart that is divided into thousandths of
an inch vertically for the indicator read- distance
ings and into whole inches horizontally
for the__________
The orthographic drawing may contain a
hidden
dashed or _______ line
In order to shoot through a test object
and project an image onto a detector or a
Radiation
sheet of film, radiography uses a source
of penetrating called _______
*scribe circles
Which of the following task would you not *transfer measurements
perform with dividers? *compare distances
<measure angles
The over speed trip device is actuated
when the turbine reaches a predeter-
10%
mined limit usually _________% above
normal full-load speed
Positive results in an offset measure-
ment mean that the MTBM is _____ or high
on the 3-o'clock side.
The coupling gap is set, and then the
offset misalignment
______ is measured
In a hydraulic system, movement de-
pressure
pends on_____
, NCCER MILLWRIGHT PRACTICE EXAM 2
Fractional dimensions are used on ob-
furniture or utility items
jects such as _______ or ______
If the cause of the problem is not
immediately understood, the process
elimination
of________is often the procedure of
choice
When applying sealant to the sealing
gland flanges, keep the sealant away
3/16
from the inside edges of the flange by at
least_______ inch
A stroboscope is triggered by a_______ Transducer
The pitch of threaded fasteners is mea-
thread
sured with a ________gauge
Liquid penetrant highlights flaws and re-
Surface cracks
veals________
A tool used to cut external threats on s
die
bolt or rod is called a ______
A bill of materials may include info on
_______ and other reference informa- special processes
tion
Engaged gears always have the same
surface speed
_____
Elevation of equipment is usually found
general arrangement
in the_____
Inspect the pulleys, rollers, and idlers for
Vibrations
unevenness or______
When cutting thin steel with Oxyfuel fuel
cutting equipment, hold the torch so that
15-20 degree angle
the tip is pointing in the direction the
torch is traveling at a _____ angle
Labby seals work BEST with materials
Grease.........
such as_____
Lubrication is the application of any sub-
Friction
stance that reduces________
