OSHA 510 Final Set Exam 2025 verified Answers

OSHA construction industry standards are found in - Correct Ans-Part 1926 of title 29 CFR Work place injuries and illnesses _____ morale and require training for the replacement worker, leading to _____ cost - Correct Ans-Lower, hidden What are OSHA's focus four hazards? - Correct Ans-Falls, electrocution, caught in or between, struck by The right of workers to be provided safety and health on the job without fear of reprisal is found in which of the following? - Correct Ans-Section 11 C of the OSHA act The general duty clause found in section 5 (a) (1) of the OSH Act: - Correct Ans-All of the above. Provides the foundational language to providing workers a safe and healthy workplace under OSHA, can be cited if no other specific OSHA standard exist to cite a specific hazard, can be applied to high incident rates of particular injuries like back injuries where the employer has no program to place to reduce or mitigate the hazards that caused these injuries. Among the rights related to OSHA recordkeeping, workers have the right to review the ______ - Correct Ans-OSHA 300 log What is the difference between horizontal and vertical standards? - Correct Ans Horizontal standards apply to general standards (first aid, fire protection) Vertical standards apply to specific industries (Construction) List an example of a consensus standard - Correct Ans-Z 87.1 ANSI Safety Glasses or Footwear List the priority of OSHA inspections; - Correct Ans-1st: imminent danger 2nd: Fatality/Catastrophe 3rd: Complaints/Referrals 4th: Programmed inspections The four major stages of an OSHA inspection are; - Correct Ans-1. Presentation of inspector credentials OSHA 510 OSHA 510 2. Opening conference 3. Walk around 4. Closing conference each citation shall remain posted until _____ or _________. - Correct Ans-Violation has been abated, 3 days List types of citation; - Correct Ans-1. Willfull 2. Serious 3. Repeated 4. Failure to abate 5. Falsifying info 6. Violation of posting Which of the following violations exist when an employer has demonstrated an intentional disregard for the requirements of the OSHA act or a plain indifference to employee safety and health? - Correct Ans-Willfull/repeat Under 29 CFR 1926 Addendum Multi employer citation policy, OSHA clarifies employers into one or more of the following four categories; - Correct Ans-1. Creating employer 2. Correcting employer 3. Controlling employer 4. Exposing employer Employers with ____ or fewer employees at all times during the last calendar year do not need to keep _____ - Correct Ans-10, Records The OSHA 300 A summary must be posted from ______ to _____ in a _______ - Correct Ans-Feb 1st - April 30th. In a common area where notices to employees are usually posted In OSHA record keeping, an _________ is the number of recordable injuries and illnesses occurring among ______ full-time workers. - Correct Ans-Incident rate, 100 Where is the definition of a competent person located? - Correct Ans-1926.32 F Where is the definition of a qualified person located? - Correct Ans-1926.32 M Program shall provide for frequent and regular inspections of the job sites, materials and equipment to be made by a ______ designated by the employer. - Correct Ans Competent person _______ shall instruct each employee in the recognition and avoidance of unsafe conditions and the regulations applicable to his work environment to control or eliminate any hazards or other exposures to illness or injury - Correct Ans-Employer OSHA 510 OSHA 510 True or false: the competent person shall be responsible for the development and maintenance of an effective fire protection and prevention program. - Correct Ans-False Fire extinguishers rated not less than 2A, shall be provided for each ______ sq ft of the protected building area. Travel distance from any point of the protected area to the nearest fire extinguisher shall not exceed _____ - Correct Ans-3,000 sq ft/ 100 ft What clearance must be maintained for the following: Between the top level of stored materials and sprinkler deflectors: Around the path of travel of fire doors: Between stored materials in a fire door opening: - Correct Ans-36" 24" 36" What are 4 general requirements for hand and power tools? - Correct Ans-Maintained in safe condition, guarding, switches, PPE When using a PFAS personal fall arrest system, what is the maximum freefall distance before a fall is decelerated? - Correct Ans-6 feet A hole is a gap or void of ______ or more in its least dimension, in a floor, roof, or other walking/working surface. - Correct Ans-2" Read rails, when used shall be installed at the height midway between the top edge of the guard rail system and the ________ - Correct Ans-Work surface Guard rail system shall be capable of withstanding, without failure, a force of at least _______ pounds applied within ___ of the top edge. - Correct Ans-200 lbs, 2" Each employee walking/working surfaces shall be protected from falling through holes more than 6 feet above lower levels by _________ erected around such holes. - Correct Ans-Covers or guardrails Anchorages used for attachment of personal fall arrest equipment shall be capable of supporting at least - Correct Ans-5,000 lbs The employer shall provide for ______ of employees in the event of a fall or shall assure that employees are able to ___________ - Correct Ans-Prompt rescue. Rescue themselves Connectors shall be protected from fall hazards of more than ____ feet or ______, whichever is less - Correct Ans-30 ft, contact w lower level OSHA 510 OSHA 510 Each employee on a scaffold more than ____ feet above a lower level shall be protected from falling through that lower level. - Correct Ans-10 feet Who is responsible to be sure that each employee exposed to a fall hazard is trained? - Correct Ans-Employer What is the difference between a danger sign and a caution sign? - Correct Ans-Danger sign is white/ black/ red Caution sign is yellow primarily with black Accident prevention tags shall be used as a temporary means of warning employees of an existing hazard, such as _____ - Correct Ans-Defective tools Cylinders shall be kept far away enough from the actual welding or cutting operation so that sparks, hot slag, or flame will not reach them. When this is impractical, __________ _________ _________ shall be provided - Correct Ans-Fire resistance shields Cylinders containing _____ or other fuel shall not be taken into confined spaces. - Correct Ans-Oxygen or Acetylene Whenever practical, all arc welding and cutting operations shall be shielded by ______________ which will protect employees and other persons working in the vicinity from the direct rays of the arc. - Correct Ans-Noncombustible or flameproof screen At what voltage is guarding required for accidental contact with electrical equipment? - Correct Ans-50v The employer shall establish and implement and assured _____________ On construction sites covering all quartzite, receptacles which are not part of the building or structure, and equipment connected by cord and p