FACILITY MAINTENANCE
TECHNICIAN EXAM 2025 QUESTIONS
AND ANSWERS
Once a repair is completed, technicians must ___. - ANS Carefully record the problem,
causes, and solutions
___ maintenance is scheduled work required to keep equipment in peak operating condition. -
ANS Preventive
___ maintenance is performed to minimize emergency work and ensure reliable and efficient
operations. - ANS Scheduled
A ___ is a document that details specific maintenance tasks to be completed. - ANS Work
order
The ___ is a federal government regulatory agency that requires all employers to provide a safe
working environment for their employees. - ANS Occupational Safety and Health
Administration (OSHA)
Fall protection equipment is required when working in elevated spaces (over ___' above the
ground) or confined spaces. - ANS 6
A ___ does not prevent the start up of equipment, but it serves as a warning to operating and
service personnel. - ANS Tagout
COPYRIGHT © 2025 BRAINBARTER ALL RIGHTS RESERVED 1
, NFPA 704, Standard system for the identification of the hazards of materials for emergency
response, uses a ___ -color diamond design to display basic information about hazardous
materials. - ANS Four
___ diagrams resemble a ladder, so they are also known as ladder diagrams. - ANS Line
Updates to an operator's manual may be distributed as ___. - ANS Service bulletins
Force can be measured in ___. - ANS Pounds
On the Celsius scale, ___ C is the freezing point. - ANS 0
___ keys are used for transmitting heavy torques in shafts and hubs that are reversed
frequently and subject to vibration. - ANS Taper
___ are used to seal close-fitting pieces of metal such as parts of an engine or pipe flanges. -
ANS Gaskets
A belt drive is a ___ mechanical drive system that uses a belt and pulleys to transfer power
between two shafts. - ANS Nonsynchronous
A(n) ___ bearing is a bearing that contains moving elements that provide a low-friction support
surface for rotating or sliding surfaces. - ANS Antifriction
The lower portion of a gearbox is usually a ___. - ANS Reservoir for lubricating internal gears
Poor bearing ___ allow dirt and other contaminants to enter the bearing components. -
ANS Seals
COPYRIGHT © 2025 BRAINBARTER ALL RIGHTS RESERVED 2
TECHNICIAN EXAM 2025 QUESTIONS
AND ANSWERS
Once a repair is completed, technicians must ___. - ANS Carefully record the problem,
causes, and solutions
___ maintenance is scheduled work required to keep equipment in peak operating condition. -
ANS Preventive
___ maintenance is performed to minimize emergency work and ensure reliable and efficient
operations. - ANS Scheduled
A ___ is a document that details specific maintenance tasks to be completed. - ANS Work
order
The ___ is a federal government regulatory agency that requires all employers to provide a safe
working environment for their employees. - ANS Occupational Safety and Health
Administration (OSHA)
Fall protection equipment is required when working in elevated spaces (over ___' above the
ground) or confined spaces. - ANS 6
A ___ does not prevent the start up of equipment, but it serves as a warning to operating and
service personnel. - ANS Tagout
COPYRIGHT © 2025 BRAINBARTER ALL RIGHTS RESERVED 1
, NFPA 704, Standard system for the identification of the hazards of materials for emergency
response, uses a ___ -color diamond design to display basic information about hazardous
materials. - ANS Four
___ diagrams resemble a ladder, so they are also known as ladder diagrams. - ANS Line
Updates to an operator's manual may be distributed as ___. - ANS Service bulletins
Force can be measured in ___. - ANS Pounds
On the Celsius scale, ___ C is the freezing point. - ANS 0
___ keys are used for transmitting heavy torques in shafts and hubs that are reversed
frequently and subject to vibration. - ANS Taper
___ are used to seal close-fitting pieces of metal such as parts of an engine or pipe flanges. -
ANS Gaskets
A belt drive is a ___ mechanical drive system that uses a belt and pulleys to transfer power
between two shafts. - ANS Nonsynchronous
A(n) ___ bearing is a bearing that contains moving elements that provide a low-friction support
surface for rotating or sliding surfaces. - ANS Antifriction
The lower portion of a gearbox is usually a ___. - ANS Reservoir for lubricating internal gears
Poor bearing ___ allow dirt and other contaminants to enter the bearing components. -
ANS Seals
COPYRIGHT © 2025 BRAINBARTER ALL RIGHTS RESERVED 2
