M142 Himars rocket launcher operators exam Questions and Answers Already Passed
What manual and appendix covers Mlrs/Himars Batallion Safety? - Answers ATP 3-09.60, Appendix G
Safety Data for the M270A1 is the same as the Himars - Answers False
To develop Mlrs/Himars safety data, there are three things that must be done. Which of the following is
not one of those three? - Answers Determine Usable Portion of the Impact Area
The surface danger zone diagram is developed and maintained in the _____. - Answers Fire direction
center
The surface danger zone consists of all but which of the following? - Answers Area E
This area is immediately behind the firing point or area that is at risk from blast and debris, which no
one can occupy. - Answers Launcher danger area
Area F is comprised of the Launcher Danger Area and the _____. - Answers Noise hazard area
This is the danger area directly in front of the firing point or operational area. - Answers Exclusion Area I.
This is the danger area between the forward limit of exclusion area I and the SDZ impact area. - Answers
Exclusion Area II
This distance is wide enough to include all debris (payload warhead skin, and rocket motor) to either
side of the target from normally functioning rounds. - Answers Distance W
A distance beyond the target adequate to contain a properly functioning rocket. - Answers Distance X
A distance short of the target sufficient to include all debris (payload warhead skin, and rocket motor)
from normally functioning rounds. - Answers Distance Y
Consists of the launcher danger area and noise hazard area - Answers Area F
There are _____ methods to compute safety data for Mlrs/Himars - Answers Three
Which of the following methods are used to compute safety data for Himars? - Answers Op Area, Pt-to-
Pt, Firing Pt
Safety computations for each of the methods used to derive safety data are completed in _____ phases.
- Answers Four
When using the safety data calculator, you are required to use check launchers. - Answers False
When using a check launcher to verify safety T data, while computing safety data via any of the
approved methods, the launcher's command data must be within +/- _____ in azimuth and quadrant
elevation of the calculated Safety T. - Answers 5 mils
What manual and appendix covers Mlrs/Himars Batallion Safety? - Answers ATP 3-09.60, Appendix G
Safety Data for the M270A1 is the same as the Himars - Answers False
To develop Mlrs/Himars safety data, there are three things that must be done. Which of the following is
not one of those three? - Answers Determine Usable Portion of the Impact Area
The surface danger zone diagram is developed and maintained in the _____. - Answers Fire direction
center
The surface danger zone consists of all but which of the following? - Answers Area E
This area is immediately behind the firing point or area that is at risk from blast and debris, which no
one can occupy. - Answers Launcher danger area
Area F is comprised of the Launcher Danger Area and the _____. - Answers Noise hazard area
This is the danger area directly in front of the firing point or operational area. - Answers Exclusion Area I.
This is the danger area between the forward limit of exclusion area I and the SDZ impact area. - Answers
Exclusion Area II
This distance is wide enough to include all debris (payload warhead skin, and rocket motor) to either
side of the target from normally functioning rounds. - Answers Distance W
A distance beyond the target adequate to contain a properly functioning rocket. - Answers Distance X
A distance short of the target sufficient to include all debris (payload warhead skin, and rocket motor)
from normally functioning rounds. - Answers Distance Y
Consists of the launcher danger area and noise hazard area - Answers Area F
There are _____ methods to compute safety data for Mlrs/Himars - Answers Three
Which of the following methods are used to compute safety data for Himars? - Answers Op Area, Pt-to-
Pt, Firing Pt
Safety computations for each of the methods used to derive safety data are completed in _____ phases.
- Answers Four
When using the safety data calculator, you are required to use check launchers. - Answers False
When using a check launcher to verify safety T data, while computing safety data via any of the
approved methods, the launcher's command data must be within +/- _____ in azimuth and quadrant
elevation of the calculated Safety T. - Answers 5 mils
