NCCER MILLWRIGHT PRACTICE EXAM 2 GUIDE 2025 PREP
1. unusual: If the seal was not properly aligned or there is excessive wear in some
bearing or shaft, wear tracks will be the indicator
2. sharpened brass putty knife: For removing hard to remove gasket materials
found on sealing surfaces, is recommended
3. Conducted on the job: Apprenticeship training is
4. distance: Charting alignment on a graph requires a chart that is divided into
thousandths of an inch vertically for the indicator readings and into whole inches
horizontally for the
5. hidden: The orthographic drawing may contain a dashed or line
6. Radiation: In order to shoot through a test object and project an image onto a
detector or a sheet of film, radiography uses a source of penetrating called
7. *scribe circles
*transfer measurements
*compare distances
<measure angles: Which of the following task would you not perform with dividers?
8. 10%: The over speed trip device is actuated when the turbine reaches a prede-
termined limit usually % above normal full-load speed
9. high: Positive results in an offset measurement mean that the MTBM is or
on the 3-o'clock side.
10. offset misalignment: The coupling gap is set, and then the is measured
11. pressure: In a hydraulic system, movement depends on
12. furniture or utility items: Fractional dimensions are used on objects such as
or
13. elimination: If the cause of the problem is not immediately understood, the
process of is often the procedure of choice
1/
13
, NCCER MILLWRIGHT PRACTICE EXAM 2 GUIDE 2025 PREP
14. 3/16: When applying sealant to the sealing gland flanges, keep the sealant away
from the inside edges of the flange by at least inch
15. Transducer: A stroboscope is triggered by a
16. thread: The pitch of threaded fasteners is measured with a gauge
17. Surface cracks: Liquid penetrant highlights flaws and reveals
18. die: A tool used to cut external threats on s bolt or rod is called a
19. special processes: A bill of materials may include info on and other
reference information
20. surface speed: Engaged gears always have the same
21. general arrangement: Elevation of equipment is usually found in the
22. Vibrations: Inspect the pulleys, rollers, and idlers for unevenness or
23. 15-20 degree angle: When cutting thin steel with Oxyfuel fuel cutting equipment,
hold the torch so that the tip is pointing in the direction the torch is traveling at a
angle
2/
13
1. unusual: If the seal was not properly aligned or there is excessive wear in some
bearing or shaft, wear tracks will be the indicator
2. sharpened brass putty knife: For removing hard to remove gasket materials
found on sealing surfaces, is recommended
3. Conducted on the job: Apprenticeship training is
4. distance: Charting alignment on a graph requires a chart that is divided into
thousandths of an inch vertically for the indicator readings and into whole inches
horizontally for the
5. hidden: The orthographic drawing may contain a dashed or line
6. Radiation: In order to shoot through a test object and project an image onto a
detector or a sheet of film, radiography uses a source of penetrating called
7. *scribe circles
*transfer measurements
*compare distances
<measure angles: Which of the following task would you not perform with dividers?
8. 10%: The over speed trip device is actuated when the turbine reaches a prede-
termined limit usually % above normal full-load speed
9. high: Positive results in an offset measurement mean that the MTBM is or
on the 3-o'clock side.
10. offset misalignment: The coupling gap is set, and then the is measured
11. pressure: In a hydraulic system, movement depends on
12. furniture or utility items: Fractional dimensions are used on objects such as
or
13. elimination: If the cause of the problem is not immediately understood, the
process of is often the procedure of choice
1/
13
, NCCER MILLWRIGHT PRACTICE EXAM 2 GUIDE 2025 PREP
14. 3/16: When applying sealant to the sealing gland flanges, keep the sealant away
from the inside edges of the flange by at least inch
15. Transducer: A stroboscope is triggered by a
16. thread: The pitch of threaded fasteners is measured with a gauge
17. Surface cracks: Liquid penetrant highlights flaws and reveals
18. die: A tool used to cut external threats on s bolt or rod is called a
19. special processes: A bill of materials may include info on and other
reference information
20. surface speed: Engaged gears always have the same
21. general arrangement: Elevation of equipment is usually found in the
22. Vibrations: Inspect the pulleys, rollers, and idlers for unevenness or
23. 15-20 degree angle: When cutting thin steel with Oxyfuel fuel cutting equipment,
hold the torch so that the tip is pointing in the direction the torch is traveling at a
angle
2/
13
