TTT1 Study guide || All Solved.
Who is the third party group that approves and endorses standards? correct answers American
National Standards Institute
What term is used to describe the documents written by members, or peers, in the industry?
correct answers Standards
A company's health, safety and environment policy should be a combination of labor regulations
and ? correct answers Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts
general clause? correct answers Employer
On a job site who should be involved in the JHA process? correct answers The Whole Crew
What does the Term SOW stand for? correct answers Scope Of Work
The letters JHA stand for what ? correct answers Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? correct answers
3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall
does the case need to by to have the correct slope? correct answers 4
Work boots with ankle support are recommended for all work sites? correct answers True
What do the letters PPE stand for ? correct answers Personal Protective Equipment
, What does the ground fault circuit interrupter (GFCI) do? correct answers Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? correct answers Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to
your anchorage be placed?extend? correct answers Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? correct
answers Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? correct answers Four feey
What is the minimum force that a work positioning system anchorage must be able to withstand?
correct answers Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection use?
correct answers 5,000 lbs
When working, how often should fall protection equipment be inspected ? correct answers Daily
before each use
According to the applicable industry standard, what is the minimum height from a lower surface
or ground where fall protection must be used? correct answers Six feet
How many pounds force is one kilo Newton(kN) correct answers 225
Who is the third party group that approves and endorses standards? correct answers American
National Standards Institute
What term is used to describe the documents written by members, or peers, in the industry?
correct answers Standards
A company's health, safety and environment policy should be a combination of labor regulations
and ? correct answers Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts
general clause? correct answers Employer
On a job site who should be involved in the JHA process? correct answers The Whole Crew
What does the Term SOW stand for? correct answers Scope Of Work
The letters JHA stand for what ? correct answers Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? correct answers
3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall
does the case need to by to have the correct slope? correct answers 4
Work boots with ankle support are recommended for all work sites? correct answers True
What do the letters PPE stand for ? correct answers Personal Protective Equipment
, What does the ground fault circuit interrupter (GFCI) do? correct answers Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? correct answers Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to
your anchorage be placed?extend? correct answers Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? correct
answers Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? correct answers Four feey
What is the minimum force that a work positioning system anchorage must be able to withstand?
correct answers Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection use?
correct answers 5,000 lbs
When working, how often should fall protection equipment be inspected ? correct answers Daily
before each use
According to the applicable industry standard, what is the minimum height from a lower surface
or ground where fall protection must be used? correct answers Six feet
How many pounds force is one kilo Newton(kN) correct answers 225
