SHP final EXAM QUESTIONS AND ANSWERS
True - CORRECT ANSWER✔✔The firefighter may be installed next to a stand-alone battery smoke
detector
False - CORRECT ANSWER✔✔When performing a full system test, you may bypass any open doors or
windows
Always enable the emergency - CORRECT ANSWER✔✔When programming an skey1,you must
False - CORRECT ANSWER✔✔When running power to the take345,polarity doesn't apply
Audible alarm (7) - CORRECT ANSWER✔✔When programming the emergency key for the skey1,which
zone/sensor type is used.
True - CORRECT ANSWER✔✔When installing a smkt3,you must use the included screws and anchors
True - CORRECT ANSWER✔✔When installing the firefighter, it is required to test the customers existing
smoke detectors
Between 6"(15cm) and 2'(61cm) from floor - CORRECT ANSWER✔✔When installing a Dw21, where is
the approved location for the sensor
Provided double sided tape - CORRECT ANSWER✔✔When installing a dw11 on a vinyl or metal frame,
what should primarily use to mount the sensor
Beans & wire caps - CORRECT ANSWER✔✔Which of the following materials can you use to group
multiple ground terminals in a takeover.
Smoke detector - CORRECT ANSWER✔✔Which of the following sensors are you not allowed to program
using a translator
, True - CORRECT ANSWER✔✔When installing the take345, you must always test the new 12v battery
before using it.
16.5 - CORRECT ANSWER✔✔What is the output voltage of transformer used to power the sky control
12" - CORRECT ANSWER✔✔What is the minimum distance for placement of a co3 from the corners of
the wall
False - CORRECT ANSWER✔✔The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14 - CORRECT ANSWER✔✔How would you program a co3 if mounted on a hallway wall
False - CORRECT ANSWER✔✔When installing a translator, you must program all of the existing sensors
as new equipment on the panel
True - CORRECT ANSWER✔✔The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze - CORRECT ANSWER✔✔Which of the following
zone/sensor types are correct when programming an smkt3
7ft - CORRECT ANSWER✔✔What it the correct height ar which to install the Pir2
Loop 2 - CORRECT ANSWER✔✔When programming a Dw21 what loop number is used
True - CORRECT ANSWER✔✔When programming a sensor into a sky control panel, you can type in the
serial number or learn it in by triggering the device.
Loop 1 Zone 3 - CORRECT ANSWER✔✔How would you program a gb2 when it is mounted on a master
bedroom ceiling
True - CORRECT ANSWER✔✔The firefighter may be installed next to a stand-alone battery smoke
detector
False - CORRECT ANSWER✔✔When performing a full system test, you may bypass any open doors or
windows
Always enable the emergency - CORRECT ANSWER✔✔When programming an skey1,you must
False - CORRECT ANSWER✔✔When running power to the take345,polarity doesn't apply
Audible alarm (7) - CORRECT ANSWER✔✔When programming the emergency key for the skey1,which
zone/sensor type is used.
True - CORRECT ANSWER✔✔When installing a smkt3,you must use the included screws and anchors
True - CORRECT ANSWER✔✔When installing the firefighter, it is required to test the customers existing
smoke detectors
Between 6"(15cm) and 2'(61cm) from floor - CORRECT ANSWER✔✔When installing a Dw21, where is
the approved location for the sensor
Provided double sided tape - CORRECT ANSWER✔✔When installing a dw11 on a vinyl or metal frame,
what should primarily use to mount the sensor
Beans & wire caps - CORRECT ANSWER✔✔Which of the following materials can you use to group
multiple ground terminals in a takeover.
Smoke detector - CORRECT ANSWER✔✔Which of the following sensors are you not allowed to program
using a translator
, True - CORRECT ANSWER✔✔When installing the take345, you must always test the new 12v battery
before using it.
16.5 - CORRECT ANSWER✔✔What is the output voltage of transformer used to power the sky control
12" - CORRECT ANSWER✔✔What is the minimum distance for placement of a co3 from the corners of
the wall
False - CORRECT ANSWER✔✔The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14 - CORRECT ANSWER✔✔How would you program a co3 if mounted on a hallway wall
False - CORRECT ANSWER✔✔When installing a translator, you must program all of the existing sensors
as new equipment on the panel
True - CORRECT ANSWER✔✔The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze - CORRECT ANSWER✔✔Which of the following
zone/sensor types are correct when programming an smkt3
7ft - CORRECT ANSWER✔✔What it the correct height ar which to install the Pir2
Loop 2 - CORRECT ANSWER✔✔When programming a Dw21 what loop number is used
True - CORRECT ANSWER✔✔When programming a sensor into a sky control panel, you can type in the
serial number or learn it in by triggering the device.
Loop 1 Zone 3 - CORRECT ANSWER✔✔How would you program a gb2 when it is mounted on a master
bedroom ceiling
