PA Appraisal License 16-20 Auto Physical
Damage
A car has adjustable door hinges. There is a giant hole on the top of the front pinnacle and the
bottom as properly among the front fender and the windshield guide column of the door.
Technician A says the space may be adjusted by means of repositioning the hinges. Technician
B says the space may be adjusted through shimming the hinges. Who is right?:
Technician A best
Technician B most effective
Both technicians are correct
Neither technicians are accurate - ANS-Technician A best
A car has had the front sheet metal changed. The fender-to-door hole is wider on the passenger
facet than on the driver aspect and the hood seems out of alignment. Technician A says that
most effective the hood latch is misaligned. Technician B says the the front structure of the
vehicle isn't always dimensionally accurate. Who is proper?
Select the Correct Answer
Technician B handiest
Technician A handiest
Both technicians are accurate
Neither technician is correct - ANS-Technician B handiest
A collision damaged automobile is found to be down (low) in top at contrary ends of the middle
phase. Technician A says the center phase has a twist situation. Technician B says the vehicle
has a diamond condition. Who is proper?
Answer Choices:
Select the Correct Answer
,Technician A simplest
Technician B only
Both technicians are correct
Neither technician is correct - ANS-Technician A best is accurate.
Explanation:
Technician A is right. The peak effect at contrary ends is a twist situation. Diamond influences
the length of the automobile.
A the front-wheel pressure vehicle became damaged in a collision, the right the front wheel
taking maximum of the impact. The estimate lists the substitute of the tire, wheel, guidance
knuckle and sub-body. Technician A says the outer CV-joint ought to not be replaced because
the boot isn't ripped. Technician B says the circumstance of the boot isn't always an indication of
damage to the CV-joint. Who is proper?
Answer Choices:
Select the Correct Answer
Technician A simplest
Technician B best
Both technicians are correct
Neither technician is accurate - ANS-Technician B handiest is correct.
Explanation:
While a torn boot (known as a "bellows boot") would indicate possible harm due to lack of
lubrication of a CV-joint, it does not always imply the joint is damaged by way of way of impact.
The rubber boot covers the joints to keep away from the entrance of dirt and dust that can
damage the joints. The standards for changing a CV-joint might encompass apparent bodily
harm, consisting of broken parts, and the introduction of overseas matter into the joint itself or
the splines.
A structural rail is being cut for sectioning. Technician A says to use a reducing torch to make
the very last reduce line. Technician B says to apply a cut-off wheel or saw to make the final
reduce. Who is right?
Technician A best
,Technician B only
Both technicians are correct
Neither technician is accurate - ANS-Technician B most effective
A technician has determined that he's going to should order a door skin for an vehicle that he is
presently repairing. Which of the following gadgets may be blanketed with the door skin whilst it
arrives?
Answer Choices:
Select the Correct Answer
Adhesives
Door handles
Nothing else may be protected
Power window supports - ANS-Nothing else will be included is accurate.
Explanation:
The order for the door skin will consist of best the door pores and skin. Any other items wanted,
together with adhesives or door handles, are additional objects that have to be ordered one
after the other.
A windshield is being replaced in a car the use of the partial cutout approach. Technician A says
to take away all of the vintage urethane besides the pinchweld primer. Technician B says the
original urethane have to continue to be in vicinity and be used as a base for the new urethane
installation. Who is accurate?
Answer Choices:
Select the Correct Answer
Technician A handiest
Technician B handiest
, Both technicians are accurate
Neither technician is accurate - ANS-Technician B only.
Explanation:
Technician B is correct. When the partial cutout technique is used, the original urethane stays in
vicinity as a base for the brand new urethane set up.
After a rear quit collision, a slim hole among the area panel and the door can also indicate:
Answer Choices:
Select the Correct Answer
The radiator is cracked.
The hood can be buckled.
The sector panel and the ground can be damaged.
The trunk lid may be broken. - ANS-The quarter panel and the floor can be broken. Is accurate.
Explanation:
This may additionally indicate that the zone panel and the floor are damaged.
After a repair to the front give up of a unibody automobile, in which structural paintings became
achieved and a sway situation changed into corrected, the sheet steel is being suited to the car.
After installing the fenders and hood, a problem arises in the shape and length of the gaps
between the left fender and hood panel, in which the fender is sort of touching the hood.
Technician A says the problem could be corrected by means of reaming the bolt hollow on the
fender flange, as a result allowing the gap to be made uniform with the other side. Technician B
says the car should be measured to peer if the sway situation become corrected. Who is right?
Answer Choices:
Select the Correct Answer
Damage
A car has adjustable door hinges. There is a giant hole on the top of the front pinnacle and the
bottom as properly among the front fender and the windshield guide column of the door.
Technician A says the space may be adjusted by means of repositioning the hinges. Technician
B says the space may be adjusted through shimming the hinges. Who is right?:
Technician A best
Technician B most effective
Both technicians are correct
Neither technicians are accurate - ANS-Technician A best
A car has had the front sheet metal changed. The fender-to-door hole is wider on the passenger
facet than on the driver aspect and the hood seems out of alignment. Technician A says that
most effective the hood latch is misaligned. Technician B says the the front structure of the
vehicle isn't always dimensionally accurate. Who is proper?
Select the Correct Answer
Technician B handiest
Technician A handiest
Both technicians are accurate
Neither technician is correct - ANS-Technician B handiest
A collision damaged automobile is found to be down (low) in top at contrary ends of the middle
phase. Technician A says the center phase has a twist situation. Technician B says the vehicle
has a diamond condition. Who is proper?
Answer Choices:
Select the Correct Answer
,Technician A simplest
Technician B only
Both technicians are correct
Neither technician is correct - ANS-Technician A best is accurate.
Explanation:
Technician A is right. The peak effect at contrary ends is a twist situation. Diamond influences
the length of the automobile.
A the front-wheel pressure vehicle became damaged in a collision, the right the front wheel
taking maximum of the impact. The estimate lists the substitute of the tire, wheel, guidance
knuckle and sub-body. Technician A says the outer CV-joint ought to not be replaced because
the boot isn't ripped. Technician B says the circumstance of the boot isn't always an indication of
damage to the CV-joint. Who is proper?
Answer Choices:
Select the Correct Answer
Technician A simplest
Technician B best
Both technicians are correct
Neither technician is accurate - ANS-Technician B handiest is correct.
Explanation:
While a torn boot (known as a "bellows boot") would indicate possible harm due to lack of
lubrication of a CV-joint, it does not always imply the joint is damaged by way of way of impact.
The rubber boot covers the joints to keep away from the entrance of dirt and dust that can
damage the joints. The standards for changing a CV-joint might encompass apparent bodily
harm, consisting of broken parts, and the introduction of overseas matter into the joint itself or
the splines.
A structural rail is being cut for sectioning. Technician A says to use a reducing torch to make
the very last reduce line. Technician B says to apply a cut-off wheel or saw to make the final
reduce. Who is right?
Technician A best
,Technician B only
Both technicians are correct
Neither technician is accurate - ANS-Technician B most effective
A technician has determined that he's going to should order a door skin for an vehicle that he is
presently repairing. Which of the following gadgets may be blanketed with the door skin whilst it
arrives?
Answer Choices:
Select the Correct Answer
Adhesives
Door handles
Nothing else may be protected
Power window supports - ANS-Nothing else will be included is accurate.
Explanation:
The order for the door skin will consist of best the door pores and skin. Any other items wanted,
together with adhesives or door handles, are additional objects that have to be ordered one
after the other.
A windshield is being replaced in a car the use of the partial cutout approach. Technician A says
to take away all of the vintage urethane besides the pinchweld primer. Technician B says the
original urethane have to continue to be in vicinity and be used as a base for the new urethane
installation. Who is accurate?
Answer Choices:
Select the Correct Answer
Technician A handiest
Technician B handiest
, Both technicians are accurate
Neither technician is accurate - ANS-Technician B only.
Explanation:
Technician B is correct. When the partial cutout technique is used, the original urethane stays in
vicinity as a base for the brand new urethane set up.
After a rear quit collision, a slim hole among the area panel and the door can also indicate:
Answer Choices:
Select the Correct Answer
The radiator is cracked.
The hood can be buckled.
The sector panel and the ground can be damaged.
The trunk lid may be broken. - ANS-The quarter panel and the floor can be broken. Is accurate.
Explanation:
This may additionally indicate that the zone panel and the floor are damaged.
After a repair to the front give up of a unibody automobile, in which structural paintings became
achieved and a sway situation changed into corrected, the sheet steel is being suited to the car.
After installing the fenders and hood, a problem arises in the shape and length of the gaps
between the left fender and hood panel, in which the fender is sort of touching the hood.
Technician A says the problem could be corrected by means of reaming the bolt hollow on the
fender flange, as a result allowing the gap to be made uniform with the other side. Technician B
says the car should be measured to peer if the sway situation become corrected. Who is right?
Answer Choices:
Select the Correct Answer
