IRONWORKER NCCER EXAM
QUESTIONS AND ANSWERS
ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE BOLT REQUIRED FOR A
3/4" DIAMETER BOLT? - Answer-2 1/4"
THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE: - Answer-SPAN
BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION MUST BE COMPLETED? -
Answer-JOIST MUST HAVE BRIDGING INSTALLED
WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED TO: - Answer-HELP
CONTROL THE LOAD
ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE GENERALLY
FOUND ON: - Answer-THE DETAIL DRAWINGS
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS KNOWN AS: - Answer-
TENSILE STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB? - Answer-COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP ELEVATION IS SHOWN AS
+130.50. WHAT IS THE DIFFERENCE IN ELEVATION? - Answer-30'3
, IN WHAT DRAWING WOULD ONE FIND THE CORRECT BOLT SIZE FOR A BEAM BEING BOLTED? - Answer-
DETAIL DRAWING
WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING TORCH? - Answer-STRIKER
EQUILIZING THE WEIGHT OF THE LOAD AT VARIOUS LIFTING POINTS IS CALLED: - Answer-
CONFIGURATION
A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD IS USED TO LAYOUT: - Answer-45 DEGREE
LINES
PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL STUDS WITH WHAT METHOD? - Answer-PING
TEST
WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT? - Answer-THE FRONT AXLE
A DOCUMENT THAT OUTLINES WEIGHTS,CRANE CONFIGURATION AND RIGGING REQUIREMENTS FOR A
LIFT IS CALLED AN: - Answer-LIFT PLAN
WHERE CAN THE BOLTING METHODS REGARDING STRUCTURAL STEEL USUALLY BE FOUND ? - Answer-IN
THE GENERAL NOTES OF THE STRUCTURAL DRAWINGS
WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL MEMBERS, THE REFERENCE POINT USED TO
DETERMINE ALL OTHER ELEVATIONS IS CALLED? - Answer-THE BENCHMARK
WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE DIMENSIONS OF 30'6" TALL AND 6 FEET WIDE?
- Answer-183FT
QUESTIONS AND ANSWERS
ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE BOLT REQUIRED FOR A
3/4" DIAMETER BOLT? - Answer-2 1/4"
THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE: - Answer-SPAN
BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION MUST BE COMPLETED? -
Answer-JOIST MUST HAVE BRIDGING INSTALLED
WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED TO: - Answer-HELP
CONTROL THE LOAD
ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE GENERALLY
FOUND ON: - Answer-THE DETAIL DRAWINGS
THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS KNOWN AS: - Answer-
TENSILE STRENGHT
WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB? - Answer-COMPOSITE DECK
THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP ELEVATION IS SHOWN AS
+130.50. WHAT IS THE DIFFERENCE IN ELEVATION? - Answer-30'3
, IN WHAT DRAWING WOULD ONE FIND THE CORRECT BOLT SIZE FOR A BEAM BEING BOLTED? - Answer-
DETAIL DRAWING
WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING TORCH? - Answer-STRIKER
EQUILIZING THE WEIGHT OF THE LOAD AT VARIOUS LIFTING POINTS IS CALLED: - Answer-
CONFIGURATION
A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD IS USED TO LAYOUT: - Answer-45 DEGREE
LINES
PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL STUDS WITH WHAT METHOD? - Answer-PING
TEST
WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT? - Answer-THE FRONT AXLE
A DOCUMENT THAT OUTLINES WEIGHTS,CRANE CONFIGURATION AND RIGGING REQUIREMENTS FOR A
LIFT IS CALLED AN: - Answer-LIFT PLAN
WHERE CAN THE BOLTING METHODS REGARDING STRUCTURAL STEEL USUALLY BE FOUND ? - Answer-IN
THE GENERAL NOTES OF THE STRUCTURAL DRAWINGS
WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL MEMBERS, THE REFERENCE POINT USED TO
DETERMINE ALL OTHER ELEVATIONS IS CALLED? - Answer-THE BENCHMARK
WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE DIMENSIONS OF 30'6" TALL AND 6 FEET WIDE?
- Answer-183FT
