J-STD-001 Exam Questions and Answers 100% Solved| Latest Update Graded A+
The width of lands shall not be reduced by more than 20% class 2+3 and 30% for class 1 for:
[D1D2D3]
Measling in laminate substrates shall not exceed 50% of the spacing between noncommon
conductors: [N1N2P3]
Crazing shall not exceed 50% of the physical spacing between noncommon conductors for:
[N1D2D3]
Prior to applying conformal coating, assemblies shall be treated to remove moisture for:
[N1N2D3]
All masking stuff for: [D1D2D3]
Staking shall not negate stress relief for: [D1D2D3]
All torque stuff for: [D1D2D3]
Rework shall be documented for: [N1N2D3]
A hardware defect shall not be repaired until the discrepancy has been documented for:
[N1D2D3]
Assemblies shall be cleaned as necessary after rework or repair: [N1N2D3]
Conformal coating shall be cured for: [D1D2D3]
, Bubbles and voids and delamination shall not bridge non common conductors for: [D1D2D3]
Coating shall be free of dewetting that exposes a conductor for: [D1D2D3]
The referee magnification for conformal coating inspection shall be what maximum and for:
4x, [A1P2D3]
Most conformal coating, encapsulation, and staking for: [D1D2D3]
Control of hand soldering shall include operator training, management, and process controls
for: [N1N2D3]
There shall be no surface damage that cuts into laminate fibers for: [N1D2D3]
Delamination or bubbles in the coverlayer of the flexible circuitry shall not span >25% of the
distance between adjacent conductive patterns for: [N1D2D3]
Assemblies shall be tested when rosin flux residue testing is required for: [N1P2D3]
Jumper wires shall be staked as specified for: [N1D2D3]
All SMT wiring for: [D1D2D3]
Who is responsible for identifying the assembly class? User
What is a defect? A condition that may affect the form, fit, or function of the item in the end
use environment
The width of lands shall not be reduced by more than 20% class 2+3 and 30% for class 1 for:
[D1D2D3]
Measling in laminate substrates shall not exceed 50% of the spacing between noncommon
conductors: [N1N2P3]
Crazing shall not exceed 50% of the physical spacing between noncommon conductors for:
[N1D2D3]
Prior to applying conformal coating, assemblies shall be treated to remove moisture for:
[N1N2D3]
All masking stuff for: [D1D2D3]
Staking shall not negate stress relief for: [D1D2D3]
All torque stuff for: [D1D2D3]
Rework shall be documented for: [N1N2D3]
A hardware defect shall not be repaired until the discrepancy has been documented for:
[N1D2D3]
Assemblies shall be cleaned as necessary after rework or repair: [N1N2D3]
Conformal coating shall be cured for: [D1D2D3]
, Bubbles and voids and delamination shall not bridge non common conductors for: [D1D2D3]
Coating shall be free of dewetting that exposes a conductor for: [D1D2D3]
The referee magnification for conformal coating inspection shall be what maximum and for:
4x, [A1P2D3]
Most conformal coating, encapsulation, and staking for: [D1D2D3]
Control of hand soldering shall include operator training, management, and process controls
for: [N1N2D3]
There shall be no surface damage that cuts into laminate fibers for: [N1D2D3]
Delamination or bubbles in the coverlayer of the flexible circuitry shall not span >25% of the
distance between adjacent conductive patterns for: [N1D2D3]
Assemblies shall be tested when rosin flux residue testing is required for: [N1P2D3]
Jumper wires shall be staked as specified for: [N1D2D3]
All SMT wiring for: [D1D2D3]
Who is responsible for identifying the assembly class? User
What is a defect? A condition that may affect the form, fit, or function of the item in the end
use environment
