MKC SWE Study Material| 331 QUESTIONS| WITH COMPLETE
SOLUTIONS
.-40*C =what in Fahrenheit - ANSWER--40*F
.(R/O) sweetwater model is found on - ANSWER-110's
.1 bar equals how many PSI? - ANSWER-14.5
.1strip line on a CASREP provides what - ANSWER-MILSTRIP info for
parts in 1parts
.87's, 175's, 225's and 270's have what model R/Os - ANSWER-village
marine
.a CAN bus has two 120 Ohms resistors installed, what is the resistance
on the bus - ANSWER-60 Ohms
.a CASREP should be submitted for any equipment malfunction or
deficiency that cannot be corrected within 48 hours and affects the
units ___ - ANSWER-primary and secondary missions
,.a hydraulic system is found to have a fault that is described as over
riding work load, how should you correct the problem - ANSWER-
adjust, repair, or replace the counterbalance valve
.A P-100 is what type of engine - ANSWER-yanmar
.a P-6 has what kind of engine - ANSWER-Honda
.a placard stating discharge of oil prohibited must be posted on all
vessels more than __ feet in length - ANSWER-26
.a potable water hose should be labeled every ___ FT - ANSWER-10
.a refrigeration system lets a small amount of oil through the
compressor. what does this mean? - ANSWER-oil is lubricating the
compressor
.a satisfactory contact percentage of gear tooth bearing contacting
across the axial length of working surface is - ANSWER-80
.a small piece of plastic and metal that is placed across two circuit ends
to make a connection or is removed to break a connection - ANSWER-
jumper
,.a squealing noise in a bearing indicates an - ANSWER-inadequate
lubrication or insufficient load
.a three stage gravity coalesce system designed to separate and remove
non-soluble oil and solids and entrained air from oily water is the -
ANSWER-vacuum gravity system
.a thrust bearing supports what type of movement - ANSWER-axial
.adding or editing detailed information on an update of a local
maintenance procedure includes - ANSWER-consumables
.after how many hours of running can you take an oil sample after an
oil change - ANSWER-25
.after you have opened the maintenance schedule when assigning a
local maintenance task to the maintenance schedule you will need to
ensure that you are in the - ANSWER-update mode
.an oil filter on a P-6 should be changed when - ANSWER-no oil filter
.approximately how long will a p-6 run on a tank(2.5 gal) of fuel -
ANSWER-4 hours
, .as wire size increases what happens to resistence and amperage -
ANSWER-resistance goes down and amperage goes up
.at what RPM does the VTEC on Honda 150 switch form the low speed
cam to the high speed cam - ANSWER-4300+
.bearings should not be stored in temperatures that exceed - ANSWER-
120*F
.before and during the operation of the R/O what type of general
inspection should be conducted - ANSWER-make sure the flowmeters
are clear and floats are visable
.before working on or removing any parts of the air compressor, you
should make sure the following conditions are completed - ANSWER-
the compressor is completely blown down and the pressure is relieved
.bent con rods will most likely cause what? - ANSWER-uneven wear of
the piston pin and bushing
.cracked con rods caused by - ANSWER-overloading
.cracking of the lands of a piston may result if - ANSWER-there is
insufficient ring groove clearance
SOLUTIONS
.-40*C =what in Fahrenheit - ANSWER--40*F
.(R/O) sweetwater model is found on - ANSWER-110's
.1 bar equals how many PSI? - ANSWER-14.5
.1strip line on a CASREP provides what - ANSWER-MILSTRIP info for
parts in 1parts
.87's, 175's, 225's and 270's have what model R/Os - ANSWER-village
marine
.a CAN bus has two 120 Ohms resistors installed, what is the resistance
on the bus - ANSWER-60 Ohms
.a CASREP should be submitted for any equipment malfunction or
deficiency that cannot be corrected within 48 hours and affects the
units ___ - ANSWER-primary and secondary missions
,.a hydraulic system is found to have a fault that is described as over
riding work load, how should you correct the problem - ANSWER-
adjust, repair, or replace the counterbalance valve
.A P-100 is what type of engine - ANSWER-yanmar
.a P-6 has what kind of engine - ANSWER-Honda
.a placard stating discharge of oil prohibited must be posted on all
vessels more than __ feet in length - ANSWER-26
.a potable water hose should be labeled every ___ FT - ANSWER-10
.a refrigeration system lets a small amount of oil through the
compressor. what does this mean? - ANSWER-oil is lubricating the
compressor
.a satisfactory contact percentage of gear tooth bearing contacting
across the axial length of working surface is - ANSWER-80
.a small piece of plastic and metal that is placed across two circuit ends
to make a connection or is removed to break a connection - ANSWER-
jumper
,.a squealing noise in a bearing indicates an - ANSWER-inadequate
lubrication or insufficient load
.a three stage gravity coalesce system designed to separate and remove
non-soluble oil and solids and entrained air from oily water is the -
ANSWER-vacuum gravity system
.a thrust bearing supports what type of movement - ANSWER-axial
.adding or editing detailed information on an update of a local
maintenance procedure includes - ANSWER-consumables
.after how many hours of running can you take an oil sample after an
oil change - ANSWER-25
.after you have opened the maintenance schedule when assigning a
local maintenance task to the maintenance schedule you will need to
ensure that you are in the - ANSWER-update mode
.an oil filter on a P-6 should be changed when - ANSWER-no oil filter
.approximately how long will a p-6 run on a tank(2.5 gal) of fuel -
ANSWER-4 hours
, .as wire size increases what happens to resistence and amperage -
ANSWER-resistance goes down and amperage goes up
.at what RPM does the VTEC on Honda 150 switch form the low speed
cam to the high speed cam - ANSWER-4300+
.bearings should not be stored in temperatures that exceed - ANSWER-
120*F
.before and during the operation of the R/O what type of general
inspection should be conducted - ANSWER-make sure the flowmeters
are clear and floats are visable
.before working on or removing any parts of the air compressor, you
should make sure the following conditions are completed - ANSWER-
the compressor is completely blown down and the pressure is relieved
.bent con rods will most likely cause what? - ANSWER-uneven wear of
the piston pin and bushing
.cracked con rods caused by - ANSWER-overloading
.cracking of the lands of a piston may result if - ANSWER-there is
insufficient ring groove clearance
