©JASONMcCONNELL 2025 ALL RIGHTS RESERVED
SHP Final Exam Questions and Answers
100% Pass
True - Answer✔The firefighter may be installed next to a stand-alone battery smoke detector
False - Answer✔When performing a full system test, you may bypass any open doors or
windows
Always enable the emergency - Answer✔When programming an skey1,you must
False - Answer✔When running power to the take345,polarity doesn't apply
Audible alarm (7) - Answer✔When programming the emergency key for the skey1,which
zone/sensor type is used.
True - Answer✔When installing a smkt3,you must use the included screws and anchors
True - Answer✔When installing the firefighter, it is required to test the customers existing
smoke detectors
Between 6"(15cm) and 2'(61cm) from floor - Answer✔When installing a Dw21, where is the
approved location for the sensor
1
, ©JASONMcCONNELL 2025 ALL RIGHTS RESERVED
Provided double sided tape - Answer✔When installing a dw11 on a vinyl or metal frame, what
should primarily use to mount the sensor
Beans & wire caps - Answer✔Which of the following materials can you use to group multiple
ground terminals in a takeover.
Smoke detector - Answer✔Which of the following sensors are you not allowed to program
using a translator
True - Answer✔When installing the take345, you must always test the new 12v battery before
using it.
16.5 - Answer✔What is the output voltage of transformer used to power the sky control
12" - Answer✔What is the minimum distance for placement of a co3 from the corners of the
wall
False - Answer✔The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14 - Answer✔How would you program a co3 if mounted on a hallway wall
False - Answer✔When installing a translator, you must program all of the existing sensors as
new equipment on the panel
True - Answer✔The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze - Answer✔Which of the following
zone/sensor types are correct when programming an smkt3
2
SHP Final Exam Questions and Answers
100% Pass
True - Answer✔The firefighter may be installed next to a stand-alone battery smoke detector
False - Answer✔When performing a full system test, you may bypass any open doors or
windows
Always enable the emergency - Answer✔When programming an skey1,you must
False - Answer✔When running power to the take345,polarity doesn't apply
Audible alarm (7) - Answer✔When programming the emergency key for the skey1,which
zone/sensor type is used.
True - Answer✔When installing a smkt3,you must use the included screws and anchors
True - Answer✔When installing the firefighter, it is required to test the customers existing
smoke detectors
Between 6"(15cm) and 2'(61cm) from floor - Answer✔When installing a Dw21, where is the
approved location for the sensor
1
, ©JASONMcCONNELL 2025 ALL RIGHTS RESERVED
Provided double sided tape - Answer✔When installing a dw11 on a vinyl or metal frame, what
should primarily use to mount the sensor
Beans & wire caps - Answer✔Which of the following materials can you use to group multiple
ground terminals in a takeover.
Smoke detector - Answer✔Which of the following sensors are you not allowed to program
using a translator
True - Answer✔When installing the take345, you must always test the new 12v battery before
using it.
16.5 - Answer✔What is the output voltage of transformer used to power the sky control
12" - Answer✔What is the minimum distance for placement of a co3 from the corners of the
wall
False - Answer✔The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14 - Answer✔How would you program a co3 if mounted on a hallway wall
False - Answer✔When installing a translator, you must program all of the existing sensors as
new equipment on the panel
True - Answer✔The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze - Answer✔Which of the following
zone/sensor types are correct when programming an smkt3
2
