Nccer boilermaker maintenance || with 100% Errorless
Answers.
Which organization requires a person to be trained to operate personal lifting equipment correct
answers OSHA
Where would the usage of a RTJ Gasket be found correct answers high pressure system
All of the following are examples of internal manway hardware except correct answers Slide
fastener
The fitting that makes it easy to dissemble threaded pipe is correct answers Union
What type of wrench measures how much a fastener is being tightened correct answers Torque
What is the purpose of a gasket? correct answers to create a seal between 2 stationary parts
What is the first consideration when making a gasket correct answers material compatibility
In order to get the bundle to line up with the shell side gasket the best tool to use to lift the
bundle is a correct answers drift pin
ring gaskets may be affected by all of the following except correct answers Number of bolts
Which way should the teeth face on a hacksaw blade correct answers Away from handle
Pressure of a 1" and 10" pipe when both are 20" tall correct answers The pressure is both the
same
When making a threaded connection and it stops on 2nd thread.... correct answers Stop,
something is wrong
When using a sealing ring on heat exchanger, what material is used to seal off in between the
floating tube sheet and test ring? correct answers Permatex
For duct bolted together there is usually some kind of correct answers gasket
If the end of a tube sheet of an exchanger has been smashed this is caused by all of the following
except correct answers The partition plate being to short
Which of the following should be removed when pressure testing the vessel correct answers
relief valve
What components are attached to the baffle on an exchanger tube bundle correct answers Tie
rods
, All of the following are safety hazards associated with vessel confined space except correct
answers improper inspection
Valves used to relieve pressure in a pipeline correct answers safety valve
What tool can be used to generate force making tightening or loosening easier correct answers
impact
Washers are used to prevent fasteners from marrying? correct answers surface
Title blocks are found where correct answers Bottom right corner
The following threaded fitting requires a thread lubricant except correct answers rubber
Taps are used to cut what type of threads? correct answers internal threads
chain hoist are primarily used for what type of lifting correct answers vertical lifting
Oxyfuel torch what valve must be turned off first correct answers Acetylene
What does SWL stand for? correct answers Safe Working Load
On a variable can (spring can) support, when are the load straps removed correct answers Just
prior to energizing the system
When rigging a valve the spring should be placed around the correct answers body
Minimum required oxygen and fuel gas storage separation when not in use and stored in open
areas correct answers 20'
When tightening up a manway or tower that has 1 1/4" x 8" stud bolts, what size wrench should
you use correct answers 2"
What should a worker do before removing flange bolts on the exchanger channel head correct
answers verify blinds are in, bleeders are open, and loto is complete
What does NPT stand for? correct answers National Pipe Thread
Flange protector should be removed from the valve when correct answers ready for installation
Which sling configuration has the greatest capacity correct answers basket
Tube sheet correct answers To pull a bundle from the shell the eye bolts should be installed on
the
Answers.
Which organization requires a person to be trained to operate personal lifting equipment correct
answers OSHA
Where would the usage of a RTJ Gasket be found correct answers high pressure system
All of the following are examples of internal manway hardware except correct answers Slide
fastener
The fitting that makes it easy to dissemble threaded pipe is correct answers Union
What type of wrench measures how much a fastener is being tightened correct answers Torque
What is the purpose of a gasket? correct answers to create a seal between 2 stationary parts
What is the first consideration when making a gasket correct answers material compatibility
In order to get the bundle to line up with the shell side gasket the best tool to use to lift the
bundle is a correct answers drift pin
ring gaskets may be affected by all of the following except correct answers Number of bolts
Which way should the teeth face on a hacksaw blade correct answers Away from handle
Pressure of a 1" and 10" pipe when both are 20" tall correct answers The pressure is both the
same
When making a threaded connection and it stops on 2nd thread.... correct answers Stop,
something is wrong
When using a sealing ring on heat exchanger, what material is used to seal off in between the
floating tube sheet and test ring? correct answers Permatex
For duct bolted together there is usually some kind of correct answers gasket
If the end of a tube sheet of an exchanger has been smashed this is caused by all of the following
except correct answers The partition plate being to short
Which of the following should be removed when pressure testing the vessel correct answers
relief valve
What components are attached to the baffle on an exchanger tube bundle correct answers Tie
rods
, All of the following are safety hazards associated with vessel confined space except correct
answers improper inspection
Valves used to relieve pressure in a pipeline correct answers safety valve
What tool can be used to generate force making tightening or loosening easier correct answers
impact
Washers are used to prevent fasteners from marrying? correct answers surface
Title blocks are found where correct answers Bottom right corner
The following threaded fitting requires a thread lubricant except correct answers rubber
Taps are used to cut what type of threads? correct answers internal threads
chain hoist are primarily used for what type of lifting correct answers vertical lifting
Oxyfuel torch what valve must be turned off first correct answers Acetylene
What does SWL stand for? correct answers Safe Working Load
On a variable can (spring can) support, when are the load straps removed correct answers Just
prior to energizing the system
When rigging a valve the spring should be placed around the correct answers body
Minimum required oxygen and fuel gas storage separation when not in use and stored in open
areas correct answers 20'
When tightening up a manway or tower that has 1 1/4" x 8" stud bolts, what size wrench should
you use correct answers 2"
What should a worker do before removing flange bolts on the exchanger channel head correct
answers verify blinds are in, bleeders are open, and loto is complete
What does NPT stand for? correct answers National Pipe Thread
Flange protector should be removed from the valve when correct answers ready for installation
Which sling configuration has the greatest capacity correct answers basket
Tube sheet correct answers To pull a bundle from the shell the eye bolts should be installed on
the
