ASE BRAKES Exam #3 | 2024-2025 LATEST UPDATED| COMPLETE
QUESTIONS WITH 100% CORRECT ANSWERS| GET IT CORRECT!!
A - (answers)The goal of burnishing the brakes after a complete brake service is to:
A. Heat the brake assembly.
B. Cool the brake assembly.
C. Set the wheel bearings.
D. Stretch the brake shoes to match the drum.
A - (answers)Which of the following is true concerning master cylinder pushrod adjustment?
A. There should be a slight gap between the pushrod and master cylinder piston.
B. It should be adjusted until the piston is pushed in slightly.
C. It should keep a slight pressure in the hydraulic system.
D. It should be adjusted at each brake pad replacement.
A - (answers)Vacuum assist from the brake booster is present with the engine running but not
present after the vehicle's engine is shut off. Which of the following could cause this condition?
A. A faulty vacuum check valve
B. A faulty vacuum booster hose
C. Low manifold vacuum
D. A leaking intake manifold
D - (answers)Technician A says an analog wheel speed sensor generates a square wave output
signal. Technician B says a digital wheel speed sensor generates an ac signal. Who is correct?
A. A
B. B
C. Both A and B
D. Neither A nor B
C - (answers)Technician A says if a vehicle has a floating rear disc brake caliper the parking
brake actuation mechanism will be inside the caliper piston. Technician B says if a vehicle has a
, fixed rear disc brake caliper the parking brake may be inside the disc brake rotor. Who is
correct?
A. A
B. B
C. Both A and B
D. Neither A nor B
D - (answers)The minimum rotor thickness specification is 1.250" (31.75 mm). Which of the
following measurements would indicate the rotor is reusable?
A. 1.115" (28.32mm)
B. 1.125" (28.57mm)
C. 1.225" (31.11mm)
D. 1.520" (38.61mm)
D - (answers)When the parking brake is released the parking brake pedal fails to return to its
most upward position. Technician A says a faulty master cylinder could be the cause. Technician
B says air trapped in the brake fluid could be the cause. Who is correct?
A. A
B. B
C. Both A and B
D. Neither A nor B
C - (answers)A complete brake job including installing a new master cylinder has been
performed on a vehicle. After a short test drive all the brakes locked up. Which of the following
is the most likely cause?
A. Brake shoes were incorrectly installed.
B. Brake pads were incorrectly installed.
C. The master cylinder was incorrectly installed.
D. The antilock braking system (ABS) sensors were not properly reset.
D - (answers)When a customer attempts to apply the parking brake, the pedal travels its full
range of motion however the parking brakes do not apply. Technician A says a faulty master
QUESTIONS WITH 100% CORRECT ANSWERS| GET IT CORRECT!!
A - (answers)The goal of burnishing the brakes after a complete brake service is to:
A. Heat the brake assembly.
B. Cool the brake assembly.
C. Set the wheel bearings.
D. Stretch the brake shoes to match the drum.
A - (answers)Which of the following is true concerning master cylinder pushrod adjustment?
A. There should be a slight gap between the pushrod and master cylinder piston.
B. It should be adjusted until the piston is pushed in slightly.
C. It should keep a slight pressure in the hydraulic system.
D. It should be adjusted at each brake pad replacement.
A - (answers)Vacuum assist from the brake booster is present with the engine running but not
present after the vehicle's engine is shut off. Which of the following could cause this condition?
A. A faulty vacuum check valve
B. A faulty vacuum booster hose
C. Low manifold vacuum
D. A leaking intake manifold
D - (answers)Technician A says an analog wheel speed sensor generates a square wave output
signal. Technician B says a digital wheel speed sensor generates an ac signal. Who is correct?
A. A
B. B
C. Both A and B
D. Neither A nor B
C - (answers)Technician A says if a vehicle has a floating rear disc brake caliper the parking
brake actuation mechanism will be inside the caliper piston. Technician B says if a vehicle has a
, fixed rear disc brake caliper the parking brake may be inside the disc brake rotor. Who is
correct?
A. A
B. B
C. Both A and B
D. Neither A nor B
D - (answers)The minimum rotor thickness specification is 1.250" (31.75 mm). Which of the
following measurements would indicate the rotor is reusable?
A. 1.115" (28.32mm)
B. 1.125" (28.57mm)
C. 1.225" (31.11mm)
D. 1.520" (38.61mm)
D - (answers)When the parking brake is released the parking brake pedal fails to return to its
most upward position. Technician A says a faulty master cylinder could be the cause. Technician
B says air trapped in the brake fluid could be the cause. Who is correct?
A. A
B. B
C. Both A and B
D. Neither A nor B
C - (answers)A complete brake job including installing a new master cylinder has been
performed on a vehicle. After a short test drive all the brakes locked up. Which of the following
is the most likely cause?
A. Brake shoes were incorrectly installed.
B. Brake pads were incorrectly installed.
C. The master cylinder was incorrectly installed.
D. The antilock braking system (ABS) sensors were not properly reset.
D - (answers)When a customer attempts to apply the parking brake, the pedal travels its full
range of motion however the parking brakes do not apply. Technician A says a faulty master
