©THEBRIGHT 2025 ALL RIGHTS RESERVED 11:11AM.
NACE CIP 2 Standards STUDY GUIDE
100% VERIFIED.
ASTM D6132 - Answer✔Standard Test method for Nondestructive Measurement of Dry Film
Thickness of Applied Coatings over Concrete using an Ultrasonic Gauge
SSPC-PA 9 - Answer✔measurement of dry coating thickness using Ultrasonic Gauge applied of
surfaces such as concrete, wood, wallboard, plastics
ATSM D 4752 - Answer✔Test method for measuring MEK resistance of Ethyl silicate zinc rich
primers by Solvent Rub
ASTM D 5402 - Answer✔Standard practice for assessing solvent resistance of organic coatings
using solvent rubs
ASTM D 6677 - Answer✔Evaluating Adhesion by Knife
ASTM D 3359 - Answer✔standard test method for measuring adhesion by tape test
ASTM D 4541 - Answer✔STANDARD TEST METHOD FOR PULL-OFF STRENGTH OF COATINGS.
USING PORTABLE ADHESION TESTERS.
ATSM D 2583 - Answer✔Standard test method for Indentation Hardness of rigid plastics by
means of a Barcol Impressor
1
, ©THEBRIGHT 2025 ALL RIGHTS RESERVED 11:11AM.
ASTM Standard G 8 - Answer✔standard test method for cathodic disbanding of pipeline coating
NACE International issues a Book Of Standards based on three classifications -
Answer✔Standard Practices (SP)
Test Methods (TM)
Materials Requirements (MP)
Change Control - Answer✔Changes are made to a standard by a formal process called
Standard Practices (SP) - Answer✔Include recommendations for
Design
Installation
Maintenance
Proper use of a material or a corrosion control system
Test Methods (TM) - Answer✔Provide the method to conduct tests so as to ascertain the
characteristics of
A material
A design
An operation
Materials Requirements (MR) - Answer✔State the necessary characteristics of a material for
which corrosion is a factor in the selection, application, and maintenance of a material
NACE #2/SSPC-SP 10 - Answer✔NEAR WHITE METAL BLAST CLEANING. When viewed without
magnification the surface shall be free from visible oil, grease, dust, dirt, mill scale, rust,
coating, oxides, corrosion products, and other foreign matter. Random staining shall be limited
to no more than 5% of each unit area of surface and may consist of lighshadows, slight streaks,
or minor discolorations caused by stains of rust, stains of mill scale or stains of previously
applied coatings.
2
NACE CIP 2 Standards STUDY GUIDE
100% VERIFIED.
ASTM D6132 - Answer✔Standard Test method for Nondestructive Measurement of Dry Film
Thickness of Applied Coatings over Concrete using an Ultrasonic Gauge
SSPC-PA 9 - Answer✔measurement of dry coating thickness using Ultrasonic Gauge applied of
surfaces such as concrete, wood, wallboard, plastics
ATSM D 4752 - Answer✔Test method for measuring MEK resistance of Ethyl silicate zinc rich
primers by Solvent Rub
ASTM D 5402 - Answer✔Standard practice for assessing solvent resistance of organic coatings
using solvent rubs
ASTM D 6677 - Answer✔Evaluating Adhesion by Knife
ASTM D 3359 - Answer✔standard test method for measuring adhesion by tape test
ASTM D 4541 - Answer✔STANDARD TEST METHOD FOR PULL-OFF STRENGTH OF COATINGS.
USING PORTABLE ADHESION TESTERS.
ATSM D 2583 - Answer✔Standard test method for Indentation Hardness of rigid plastics by
means of a Barcol Impressor
1
, ©THEBRIGHT 2025 ALL RIGHTS RESERVED 11:11AM.
ASTM Standard G 8 - Answer✔standard test method for cathodic disbanding of pipeline coating
NACE International issues a Book Of Standards based on three classifications -
Answer✔Standard Practices (SP)
Test Methods (TM)
Materials Requirements (MP)
Change Control - Answer✔Changes are made to a standard by a formal process called
Standard Practices (SP) - Answer✔Include recommendations for
Design
Installation
Maintenance
Proper use of a material or a corrosion control system
Test Methods (TM) - Answer✔Provide the method to conduct tests so as to ascertain the
characteristics of
A material
A design
An operation
Materials Requirements (MR) - Answer✔State the necessary characteristics of a material for
which corrosion is a factor in the selection, application, and maintenance of a material
NACE #2/SSPC-SP 10 - Answer✔NEAR WHITE METAL BLAST CLEANING. When viewed without
magnification the surface shall be free from visible oil, grease, dust, dirt, mill scale, rust,
coating, oxides, corrosion products, and other foreign matter. Random staining shall be limited
to no more than 5% of each unit area of surface and may consist of lighshadows, slight streaks,
or minor discolorations caused by stains of rust, stains of mill scale or stains of previously
applied coatings.
2
