Dante Level 1-3 EXAM QUESTIONS WITH ACTUAL CORRECT
DETAILED ANSWERS GRADED A +
Dante audio streams over WiFi networks [are _______________________]. - ANSWER-not
supported
The bit depth of an audio system dictates - ANSWER-The amplitude resolution of each sample
Does Dante support MIDI - ANSWER-No. Dante only transports audio data and does not
interfere with MIDI.
Is there any advantage to using automatic IP addressing on a Dante network - ANSWER-Yes.
Automatic addressing ensures that devices create a working LAN.
How are device names used in Dante - ANSWER-Subscriptions are made from name to name
Dante works best with [______________] switches - ANSWER-gigabit
On a Dante network, latency is - ANSWER-deterministic, set per device
As sample rate is increased on a device, what other property is usually changed - ANSWER-
Channel count is reduced
,Where do Dante settings reside? - ANSWER-On individual Dante devices
In the Dante Controller Routing tab, a green check mark indicates - ANSWER-Subscription
successful
Which of the following are diagnostic features of Dante Controller? (check all that apply) -
ANSWER-1. Latency monitoring
2. Clock monitoring
How does Dante interact with Energy Efficient Ethernet (EEE) switches? - ANSWER-EEE switches
are not recommended for use with Dante
When should fiber be used for an Ethernet connection? - ANSWER-When runs over 100 meters
are required.
The easiest way to get IP addresses for a functional stand-alone Dante network is for all devices
and computers to - ANSWER-Use the "obtain an IP Address Automatically" setting
If a network is only used for Dante and has only one network switch, then - ANSWER-The
network does not require a managed switch
Does Dante require special network cabling? - ANSWER-Regular CAT5E or CAT6 Ethernet cable is
recommended
How are devices added to a Dante network - ANSWER-Devices are automatically discovered and
displayed in Dante Controller
Dante uses [_________________________] switches. - ANSWER-standard
, How are devices restored to a Dante network after power cycle - ANSWER-Devices and
connections are automatically restored
What does the Dante Clock Master do - ANSWER-Provides synchronization for all Dante devices
on the network
Does a Dante network require special configuration for clocking - ANSWER-No. A Clock Master is
always automatically elected by Dante
A[______________] network topology is a best practice for Dante. - ANSWER-star
What is latency - ANSWER-Latency is the audio signal delay in any audio system.
Dante transmitters are sources. Dante receivers are [______________________]. - ANSWER-
destinations
The names of devices and channels in Dante are - ANSWER-User-definable and remembered by
devices.
The default Dante latency of 1 millisecond is - ANSWER-very low and suitable for the majority of
applications
What are the steps to delete a subscription in Dante Controller? (drag to put steps in the correct
order) - ANSWER-1. Open both transmitter and receiver to expose channels
2. Click green checkmark at intersection of channels you wish to unsubscribe
3. Wait for green checkmark to disappear
DETAILED ANSWERS GRADED A +
Dante audio streams over WiFi networks [are _______________________]. - ANSWER-not
supported
The bit depth of an audio system dictates - ANSWER-The amplitude resolution of each sample
Does Dante support MIDI - ANSWER-No. Dante only transports audio data and does not
interfere with MIDI.
Is there any advantage to using automatic IP addressing on a Dante network - ANSWER-Yes.
Automatic addressing ensures that devices create a working LAN.
How are device names used in Dante - ANSWER-Subscriptions are made from name to name
Dante works best with [______________] switches - ANSWER-gigabit
On a Dante network, latency is - ANSWER-deterministic, set per device
As sample rate is increased on a device, what other property is usually changed - ANSWER-
Channel count is reduced
,Where do Dante settings reside? - ANSWER-On individual Dante devices
In the Dante Controller Routing tab, a green check mark indicates - ANSWER-Subscription
successful
Which of the following are diagnostic features of Dante Controller? (check all that apply) -
ANSWER-1. Latency monitoring
2. Clock monitoring
How does Dante interact with Energy Efficient Ethernet (EEE) switches? - ANSWER-EEE switches
are not recommended for use with Dante
When should fiber be used for an Ethernet connection? - ANSWER-When runs over 100 meters
are required.
The easiest way to get IP addresses for a functional stand-alone Dante network is for all devices
and computers to - ANSWER-Use the "obtain an IP Address Automatically" setting
If a network is only used for Dante and has only one network switch, then - ANSWER-The
network does not require a managed switch
Does Dante require special network cabling? - ANSWER-Regular CAT5E or CAT6 Ethernet cable is
recommended
How are devices added to a Dante network - ANSWER-Devices are automatically discovered and
displayed in Dante Controller
Dante uses [_________________________] switches. - ANSWER-standard
, How are devices restored to a Dante network after power cycle - ANSWER-Devices and
connections are automatically restored
What does the Dante Clock Master do - ANSWER-Provides synchronization for all Dante devices
on the network
Does a Dante network require special configuration for clocking - ANSWER-No. A Clock Master is
always automatically elected by Dante
A[______________] network topology is a best practice for Dante. - ANSWER-star
What is latency - ANSWER-Latency is the audio signal delay in any audio system.
Dante transmitters are sources. Dante receivers are [______________________]. - ANSWER-
destinations
The names of devices and channels in Dante are - ANSWER-User-definable and remembered by
devices.
The default Dante latency of 1 millisecond is - ANSWER-very low and suitable for the majority of
applications
What are the steps to delete a subscription in Dante Controller? (drag to put steps in the correct
order) - ANSWER-1. Open both transmitter and receiver to expose channels
2. Click green checkmark at intersection of channels you wish to unsubscribe
3. Wait for green checkmark to disappear
