INVENTOR PRACTICE TEST 1
QUESTIONS & ANSWERS
2. Open View Management.ipt Change the Ground Plane settings. Add 10 mm to the
Minor Grid Display What is the new setting? Answer: ## mm - ANSWER 30
4. Open Assembly Constraints.iam Constrain the two components. Make the
relationship from the base of the bolt to the base of the nut. No offset. What is the
distance of the remaining grip length (bolt sticking out)? Answer: #.### inches -
ANSWER 0.787
6. Open Project Centerlines.idw. Finish the drawing by adding centerlines and
dimensions.What is the dimension, in inches, of the centerline from the bottom edge of
the plate? Answer: #.## inches - ANSWER 3.50
13. Open Pattern.ipt Create a view representation of the current view. A view has
already been created. Use the next default. What is the default name for this view? -
ANSWER View2
14. Which of the following options are available when launching a new project? -
ANSWER New Single User Project,
New Vault Project
15. What is the parameter name of the master hole? - ANSWER d14
17. What is the surface area of the tilted surface? - ANSWER 2.721
7. Open Plate.idw of Plate.ipt. Create a detail view on the right side of the drawing
field.By default, what is the View Identifier for the first view created on the drawing? -
ANSWER A
8. Open Pattern.ipt Create a circular pattern using the center hole as the axis of
rotation.What is the distance between the centers of two adjacent holes?Answer:
##.### mm - ANSWER 73.093
12. Open Work Feature.ipt Create the bridge in the part as shown, 0.5" width. Use the
sketch shown in the view. Create the bridge on a workplane 2 inches down inside the
box from the opening. Extrusion depth is 0.25". What is the surface area of the tiled
area? #.## in2 - ANSWER 2.75
25. What type of Inventor file is used to show and exploded assembly view? - ANSWER
Presentation File (.ipn)
QUESTIONS & ANSWERS
2. Open View Management.ipt Change the Ground Plane settings. Add 10 mm to the
Minor Grid Display What is the new setting? Answer: ## mm - ANSWER 30
4. Open Assembly Constraints.iam Constrain the two components. Make the
relationship from the base of the bolt to the base of the nut. No offset. What is the
distance of the remaining grip length (bolt sticking out)? Answer: #.### inches -
ANSWER 0.787
6. Open Project Centerlines.idw. Finish the drawing by adding centerlines and
dimensions.What is the dimension, in inches, of the centerline from the bottom edge of
the plate? Answer: #.## inches - ANSWER 3.50
13. Open Pattern.ipt Create a view representation of the current view. A view has
already been created. Use the next default. What is the default name for this view? -
ANSWER View2
14. Which of the following options are available when launching a new project? -
ANSWER New Single User Project,
New Vault Project
15. What is the parameter name of the master hole? - ANSWER d14
17. What is the surface area of the tilted surface? - ANSWER 2.721
7. Open Plate.idw of Plate.ipt. Create a detail view on the right side of the drawing
field.By default, what is the View Identifier for the first view created on the drawing? -
ANSWER A
8. Open Pattern.ipt Create a circular pattern using the center hole as the axis of
rotation.What is the distance between the centers of two adjacent holes?Answer:
##.### mm - ANSWER 73.093
12. Open Work Feature.ipt Create the bridge in the part as shown, 0.5" width. Use the
sketch shown in the view. Create the bridge on a workplane 2 inches down inside the
box from the opening. Extrusion depth is 0.25". What is the surface area of the tiled
area? #.## in2 - ANSWER 2.75
25. What type of Inventor file is used to show and exploded assembly view? - ANSWER
Presentation File (.ipn)
