3/8/25, 10:04 AM Aumt Brake Final Exam
Aumt Brake Final Exam
AUMT BRAKE FINAL ACTUAL EXAM 2025 NEWEST
VERSION WITH ACCURATE 131 QUESTIONS AND
CORRECT DETAILED ANSWERS \\VERIFIED ANSWERS
ALREADY GRADED A+ BRAND NEW 2025
Terms in this set (131)
Tech A says that most Tech A
brake drums are designed
to be machined if minor
surface issues are present.
Tech B says that brake
drums can be reused if
they are machined larger
than specifications, as
long as the surface is
smooth. Who is correct?
All of the following It is standard practice to hone out deep pits in the
statements with respect to wheel cylinder bore.
a wheel cylinder and
piston are true EXCEPT:
1/23
,3/8/25, 10:04 AM Aumt Brake Final Exam
The component of the wheel cylinder
drum brake system
attached to the backing
plate is the:
Tech A says that when a Tech A
race is fully seated, a
sharp metallic sound is
produced when
installation is complete.
Tech B says that to be sure
a race is fully seated, the
wheel bearing adjusting
nut should be tightened to
at least 100 ft-lbs of
torque, which will finish
seating it. Who is correct?
Tech A says that when both A and B
performing a brake job on
the rear axle of an older
vehicle, inspection finds
brake fluid under the dust
boot; the wheel cylinder
should be replaced. Tech
B says that when a drum
brake return spring has
failed, springs on both
rear wheels need to be
replaced. Who is correct?
2/23
, 3/8/25, 10:04 AM Aumt Brake Final Exam
Tech A says to use an air Tech B
hose to clean the backing
plate of dust and
contamination. Tech B says
to use a water-based
cleaning solution to clean
the backing plate of dust
and contamination. Who is
correct?
Among the tools used to hold the pistons in the wheel cylinder while the brake
diagnose and repair drum shoes are removed.
brake systems, the wheel
cylinder piston clamp is
used to:
Choose the correct The backing plate has holes stamped in it.
statement:
Tech A says that duo- Tech A
servo brake shoes are
only anchored on the top.
Tech B says that duo-
servo brakes typically use
single-piston wheel
cylinders. Who is correct?
Tech A says that both Tech B
secondary shoes should
be installed on the
passenger side of the
vehicle. Tech B says that
the lining on the primary
shoe is typically shorter in
length than the lining on
the secondary shoe. Who
is correct?
3/23
Aumt Brake Final Exam
AUMT BRAKE FINAL ACTUAL EXAM 2025 NEWEST
VERSION WITH ACCURATE 131 QUESTIONS AND
CORRECT DETAILED ANSWERS \\VERIFIED ANSWERS
ALREADY GRADED A+ BRAND NEW 2025
Terms in this set (131)
Tech A says that most Tech A
brake drums are designed
to be machined if minor
surface issues are present.
Tech B says that brake
drums can be reused if
they are machined larger
than specifications, as
long as the surface is
smooth. Who is correct?
All of the following It is standard practice to hone out deep pits in the
statements with respect to wheel cylinder bore.
a wheel cylinder and
piston are true EXCEPT:
1/23
,3/8/25, 10:04 AM Aumt Brake Final Exam
The component of the wheel cylinder
drum brake system
attached to the backing
plate is the:
Tech A says that when a Tech A
race is fully seated, a
sharp metallic sound is
produced when
installation is complete.
Tech B says that to be sure
a race is fully seated, the
wheel bearing adjusting
nut should be tightened to
at least 100 ft-lbs of
torque, which will finish
seating it. Who is correct?
Tech A says that when both A and B
performing a brake job on
the rear axle of an older
vehicle, inspection finds
brake fluid under the dust
boot; the wheel cylinder
should be replaced. Tech
B says that when a drum
brake return spring has
failed, springs on both
rear wheels need to be
replaced. Who is correct?
2/23
, 3/8/25, 10:04 AM Aumt Brake Final Exam
Tech A says to use an air Tech B
hose to clean the backing
plate of dust and
contamination. Tech B says
to use a water-based
cleaning solution to clean
the backing plate of dust
and contamination. Who is
correct?
Among the tools used to hold the pistons in the wheel cylinder while the brake
diagnose and repair drum shoes are removed.
brake systems, the wheel
cylinder piston clamp is
used to:
Choose the correct The backing plate has holes stamped in it.
statement:
Tech A says that duo- Tech A
servo brake shoes are
only anchored on the top.
Tech B says that duo-
servo brakes typically use
single-piston wheel
cylinders. Who is correct?
Tech A says that both Tech B
secondary shoes should
be installed on the
passenger side of the
vehicle. Tech B says that
the lining on the primary
shoe is typically shorter in
length than the lining on
the secondary shoe. Who
is correct?
3/23
