OREGON STATE BOARD TATTOO TEST
QUESTIONS WITH CORRECT ANSWERS
sharps container - Answer-A puncture-resistant, leak proof container that can be closed
for handling, transportation, storage and disposal. Must be labeled with a biohazard
symbol
210 hours - Answer-How many total hours of theory must be completed
30 days - Answer-How long is a temporary tattoo license good for
2 times in a 12 month period - Answer-How often can you renew a temporary tattoo
license
20 days - Answer-How long do you have to request a temporary tattoo license renewal
before the services are provided
24 hours - Answer-How long before do you need to notify the office of a change in work
location for a temporary tattoo license
1 year - Answer-How long is a tattoo license valid for
3 years - Answer-How long can a tattoo license be inactive for
10 hours, 8 hours - Answer-How many hours of continuing education per year and how
many can carry over to the next year
A commercial supplier - Answer-Where do inks and dyes need to be purchased from
Manufacturer's instructions - Answer-All coverings and bandages must be used
according to...
Prescription by a physician - Answer-When is the only time a person under 18 can
legally get a tattoo
All license holders - Answer-Who is responsible for the cleanliness of the common area
Closed, labeled containers - Answer-How should chemicals be stored
2 - Answer-How many people on the board are tattoo artists
40-60 kilohertz - Answer-What must the ultrasonic cleanse operate at
, Integrator strip - Answer-What monitors essential conditions of steam sterilization for
each autoclaved cycle
60 days - Answer-How long do steam sterilization integrators need to be kept for
Indicator strip - Answer-Sterilized instruments must be stored in individually packaged
sterilization pouches that include an
The date sterilization was performed - Answer-What needs to be on the sterilization
pouch before it's stored
2 years - Answer-How long do spore test results need to be kept on file
Springs - Answer-Allow the needle to bounce up and down penetrating the skin
Contacts - Answer-Allow for a complete electrical current when connected
Contact caps - Answer-Cover the contact points to allow them to be flush for better
connectivity
Soldering lug - Answer-Where the wires are saudered allowing for better contact
Binding post - Answer-Holds contact screw and allows it to be adjusted
Machine frame - Answer-Keeps the machine steady and holds the pieces together
Band hook - Answer-Where the rubber bands are held secure
Needle bar - Answer-Holds the number of needles needed for the work
Needle tube - Answer-Protects the needle bar
Tube cap - Answer-Covers the tip of the needle tube
Armature bar - Answer-Holds the needle bar and drives it up and down
Machine coil - Answer-Determines the amount of power the machine has
Screws and washers - Answer-Hold the various parts together
Capacitor - Answer-Holds extra charge and a battery set up
Rubber bands - Answer-Help hold the pieces in place and keep them steady
Magnum - Answer-Two shader bars offset and soldered together, one on top of the
other
QUESTIONS WITH CORRECT ANSWERS
sharps container - Answer-A puncture-resistant, leak proof container that can be closed
for handling, transportation, storage and disposal. Must be labeled with a biohazard
symbol
210 hours - Answer-How many total hours of theory must be completed
30 days - Answer-How long is a temporary tattoo license good for
2 times in a 12 month period - Answer-How often can you renew a temporary tattoo
license
20 days - Answer-How long do you have to request a temporary tattoo license renewal
before the services are provided
24 hours - Answer-How long before do you need to notify the office of a change in work
location for a temporary tattoo license
1 year - Answer-How long is a tattoo license valid for
3 years - Answer-How long can a tattoo license be inactive for
10 hours, 8 hours - Answer-How many hours of continuing education per year and how
many can carry over to the next year
A commercial supplier - Answer-Where do inks and dyes need to be purchased from
Manufacturer's instructions - Answer-All coverings and bandages must be used
according to...
Prescription by a physician - Answer-When is the only time a person under 18 can
legally get a tattoo
All license holders - Answer-Who is responsible for the cleanliness of the common area
Closed, labeled containers - Answer-How should chemicals be stored
2 - Answer-How many people on the board are tattoo artists
40-60 kilohertz - Answer-What must the ultrasonic cleanse operate at
, Integrator strip - Answer-What monitors essential conditions of steam sterilization for
each autoclaved cycle
60 days - Answer-How long do steam sterilization integrators need to be kept for
Indicator strip - Answer-Sterilized instruments must be stored in individually packaged
sterilization pouches that include an
The date sterilization was performed - Answer-What needs to be on the sterilization
pouch before it's stored
2 years - Answer-How long do spore test results need to be kept on file
Springs - Answer-Allow the needle to bounce up and down penetrating the skin
Contacts - Answer-Allow for a complete electrical current when connected
Contact caps - Answer-Cover the contact points to allow them to be flush for better
connectivity
Soldering lug - Answer-Where the wires are saudered allowing for better contact
Binding post - Answer-Holds contact screw and allows it to be adjusted
Machine frame - Answer-Keeps the machine steady and holds the pieces together
Band hook - Answer-Where the rubber bands are held secure
Needle bar - Answer-Holds the number of needles needed for the work
Needle tube - Answer-Protects the needle bar
Tube cap - Answer-Covers the tip of the needle tube
Armature bar - Answer-Holds the needle bar and drives it up and down
Machine coil - Answer-Determines the amount of power the machine has
Screws and washers - Answer-Hold the various parts together
Capacitor - Answer-Holds extra charge and a battery set up
Rubber bands - Answer-Help hold the pieces in place and keep them steady
Magnum - Answer-Two shader bars offset and soldered together, one on top of the
other
