2/17/25, 1:12 PM PA Appraisers License Exam Questions and Answers | Version | Already Verified Answers Flashcards | Quizlet
PA Appraisers License Exam Questions and
Answers | Version | Already Verified Answers
Save
Terms in this set (347)
How is a diamond By pulling the damage for length. Diamond is a length
condition fixed? condition.
When measuring a Width is calculated from the center out, so a value of
unibody vehicle, it is -111mm on the left rail shows sway to the right and in
discovered that the left toward centerline.
front rail is 111mm from
spec in width. What
condition is this?
A collision damaged Twist condition.
vehicle is discovered to be
down in height at
opposite end of the
center section.
https://quizlet.com/1006822572/pa-appraisers-license-exam-questions-and-answers-version-already-verified-answers-flash-cards/?new 1/9
, 2/17/25, 1:12 PM PA Appraisers License Exam Questions and Answers | Version | Already Verified Answers Flashcards | Quizlet
When diagnosing the Tech A. When a frame rail's relationship to the vehicle
damage to a full frame centerline is changed, such as pushed either to the
assembly on a sport utility left or right, the condition is known as sway. "Twist" is
vehicle, it is determined referred as the condition of the frame when entire
that the left side frame rail sections are driven higher or lower than the opposite
is higher than the right side.
side frame rail. Technician
A says the damaged state
is known as a twist
condition. Technician B
says a sway condition
exists. Who is right?
Metal fillers contain Fiberglass offers more resistance to moisture
different ingredients that
provide fillers with special
properties.
HSLA High Strength Low Alloy
When replacing the floor An overlap joint
pan in the trunk area, what
joint should be used to
join the new pan to the
existing floor?
When acoustical foam is It must be replaced with acoustical foam.
removed during the repair:
When setting up a three- Starting in the center section is the correct method.
dimensional measuring
system, it should be setup
on an undamaged area.
What is the plastic Black Vapor Canister
box in rear of the car?
Grinding or squeaking Bad Bearings
from wheel is a sign of
what?
https://quizlet.com/1006822572/pa-appraisers-license-exam-questions-and-answers-version-already-verified-answers-flash-cards/?new 2/9
PA Appraisers License Exam Questions and
Answers | Version | Already Verified Answers
Save
Terms in this set (347)
How is a diamond By pulling the damage for length. Diamond is a length
condition fixed? condition.
When measuring a Width is calculated from the center out, so a value of
unibody vehicle, it is -111mm on the left rail shows sway to the right and in
discovered that the left toward centerline.
front rail is 111mm from
spec in width. What
condition is this?
A collision damaged Twist condition.
vehicle is discovered to be
down in height at
opposite end of the
center section.
https://quizlet.com/1006822572/pa-appraisers-license-exam-questions-and-answers-version-already-verified-answers-flash-cards/?new 1/9
, 2/17/25, 1:12 PM PA Appraisers License Exam Questions and Answers | Version | Already Verified Answers Flashcards | Quizlet
When diagnosing the Tech A. When a frame rail's relationship to the vehicle
damage to a full frame centerline is changed, such as pushed either to the
assembly on a sport utility left or right, the condition is known as sway. "Twist" is
vehicle, it is determined referred as the condition of the frame when entire
that the left side frame rail sections are driven higher or lower than the opposite
is higher than the right side.
side frame rail. Technician
A says the damaged state
is known as a twist
condition. Technician B
says a sway condition
exists. Who is right?
Metal fillers contain Fiberglass offers more resistance to moisture
different ingredients that
provide fillers with special
properties.
HSLA High Strength Low Alloy
When replacing the floor An overlap joint
pan in the trunk area, what
joint should be used to
join the new pan to the
existing floor?
When acoustical foam is It must be replaced with acoustical foam.
removed during the repair:
When setting up a three- Starting in the center section is the correct method.
dimensional measuring
system, it should be setup
on an undamaged area.
What is the plastic Black Vapor Canister
box in rear of the car?
Grinding or squeaking Bad Bearings
from wheel is a sign of
what?
https://quizlet.com/1006822572/pa-appraisers-license-exam-questions-and-answers-version-already-verified-answers-flash-cards/?new 2/9
