TPC 108 Powertools
A dado saw blade set is a combination of __________ and __________ blades. -
ANS-cutters and chippers
A light-duty power nibbler has a cutting speed of ________ fpm. - ANS-6
A rip guide limits the width of the cut to about - ANS-6 inches
A saw protractor has a moveable arm which can be set in small increments up to - ANS-180
degrees
Advancing a router too fast causes - ANS-force feeding- gauges and splinters
An electric screwdriver uses a __________ to hold the bit in place. - ANS-spindle- Nose
Piece
Do NOT use a pad sander for - ANS-removal of Paint and Varnish
Dressing a grinding wheel means to - ANS-expose grit
Electric nutrunners operate at no-load speeds of - ANS-0-2500 rev. per minute
Electric nutrunners operate at no-load speeds of - ANS-0-2500rpm
Examples of template routing include - ANS-Dove Tail Joints and Hinge Butt Mortising
How many blows per minute does an electric hammer deliver? - ANS-2000-3000 blows per
minute
How often should the grease fittings in a pneumatic grinder be greased? - ANS-40 hours
Most moisture is removed from a pneumatic tool's air supply at the - ANS-compressor
Open-coat 16-24-30 sanding disks are best for - ANS-To remove paint and smooth surface
irregularities
Pneumatic grinders often fail because of - ANS-improper lubrication
The blade motion of a reciprocating saw is - ANS-backstroke cut
The finer the grain on a grinder wheel, the - ANS-More cutting edges on the wheel and the
faster it cuts
The maximum safe speed for a grinding wheel with silicate bond is - ANS-6500 sfm
The positive-drive clutch mechanism remains engaged as long as you press the - ANS-bit on
the fastener
The positive-drive clutch mechanism remains engaged as long as you press the - ANS-bit on
the fastener
The rip blade has - ANS-chisel shape for rapid cutting making splinters
The router uses different types of __________ to make different cuts. - ANS-bits
The size of a circular saw equals the - ANS-Diameter
The size of a pneumatic drill is determined by the - ANS-largest bit the chuck can hold
The size of a power wrench is determined by the size of its - ANS-drive
The threaded shaft on which the blade of a circular saw is mounted is called the - ANS-arbor
To put a screwdriver tip back in shape, first grind the tip to a _______° angle to the shank. -
ANS-90 degree
What are the three factors that determine the proper rate of feed when using a router? -
ANS-Texture, Size of the bit, Depth of cut
What are the three factors that determine the proper rate of feed when using a router? -
ANS-Texture, Size of the bit, Depth of cut
What device is used to tighten the collet chuck on a router? - ANS-wrench
A dado saw blade set is a combination of __________ and __________ blades. -
ANS-cutters and chippers
A light-duty power nibbler has a cutting speed of ________ fpm. - ANS-6
A rip guide limits the width of the cut to about - ANS-6 inches
A saw protractor has a moveable arm which can be set in small increments up to - ANS-180
degrees
Advancing a router too fast causes - ANS-force feeding- gauges and splinters
An electric screwdriver uses a __________ to hold the bit in place. - ANS-spindle- Nose
Piece
Do NOT use a pad sander for - ANS-removal of Paint and Varnish
Dressing a grinding wheel means to - ANS-expose grit
Electric nutrunners operate at no-load speeds of - ANS-0-2500 rev. per minute
Electric nutrunners operate at no-load speeds of - ANS-0-2500rpm
Examples of template routing include - ANS-Dove Tail Joints and Hinge Butt Mortising
How many blows per minute does an electric hammer deliver? - ANS-2000-3000 blows per
minute
How often should the grease fittings in a pneumatic grinder be greased? - ANS-40 hours
Most moisture is removed from a pneumatic tool's air supply at the - ANS-compressor
Open-coat 16-24-30 sanding disks are best for - ANS-To remove paint and smooth surface
irregularities
Pneumatic grinders often fail because of - ANS-improper lubrication
The blade motion of a reciprocating saw is - ANS-backstroke cut
The finer the grain on a grinder wheel, the - ANS-More cutting edges on the wheel and the
faster it cuts
The maximum safe speed for a grinding wheel with silicate bond is - ANS-6500 sfm
The positive-drive clutch mechanism remains engaged as long as you press the - ANS-bit on
the fastener
The positive-drive clutch mechanism remains engaged as long as you press the - ANS-bit on
the fastener
The rip blade has - ANS-chisel shape for rapid cutting making splinters
The router uses different types of __________ to make different cuts. - ANS-bits
The size of a circular saw equals the - ANS-Diameter
The size of a pneumatic drill is determined by the - ANS-largest bit the chuck can hold
The size of a power wrench is determined by the size of its - ANS-drive
The threaded shaft on which the blade of a circular saw is mounted is called the - ANS-arbor
To put a screwdriver tip back in shape, first grind the tip to a _______° angle to the shank. -
ANS-90 degree
What are the three factors that determine the proper rate of feed when using a router? -
ANS-Texture, Size of the bit, Depth of cut
What are the three factors that determine the proper rate of feed when using a router? -
ANS-Texture, Size of the bit, Depth of cut
What device is used to tighten the collet chuck on a router? - ANS-wrench
