Locksmith Study Guide Questions/Answer 2025/2026 Graded
A+
14 - A Licensee who moves or changes employers shall notify the Oklahoma
Department of Labor within how many days?
High blood sugar - A technician is weak, having chills and cannot seem to get enough to
drink. What is the likely cause of the technicians symptoms?
Persons who sell, install, and service alarm systems - The Oklahoma Alarm and
Locksmith Industry Act applies to:
Short Wafer - What type of tumbler is most commonly used in a file cabinet lock?
$1000 - what is the maximum amount of administrative fines that can be levied against
any person for violations of the Oklahoma Alarm and locksmith Industry Act.
an overlapping astragal - A coordinator is required on a pair of fire doors having:
Carbide - With proper care, which cutter material typically provides the longest use?
Make the installation look better - Thru-bolt trim is used on many mortise locks to:
With the more stringent standard - If conflict exists between adopted references, the
reference that applies shall be the one:
Weiser - What brand of lock does a WR3 or 1054WB key blank fit?
A key is required to lock the room - A classroom function lock is designed so that:
Dexter - The key shown above matches
Bouncing the top pins above the shear line - Pick guns work by:
Weslock - What brand of lock does WK2 or 1175 key blank fit?
Master - What brand of lock does a M1 or 1092 key blank fit?
Requires a key or card from the outside in order to enter - A hotel function lockset is one
that:
Tension Wrench and Hook Pick - Which tools are used to manipulate a lock?
Screws on the inside of the knob - When removing a Kwikset entrance set, what should
the locksmith remove first?
, Improper lubricating the lock - Difficulty inserting or removing the key blank during
impressioning is caused by:
Brass - Of the following materials, which key blank produces the most obvious marks?
Locate a 3-pronged outlet - A power tool has a 3-pronged plug but the only available
outlets are 2-pronged. What should a technician do?
Three - How many trainees per job site can work under the supervision of a licensed
technician?
0.003 - What length of graduation is found in a standard universal pin kit with 0.115
diameter pins?
Insert the key change from the back of the wheel pack - When changing a Standard
Group 2 combination, the technician should dial the old combination on the change
mark and:
Is not lockable - A passage set is a lockset that
Hazardous vapors or fumes - What is the primary hazard when working with gas-
powered tools in an indoor space?
Three - When using a portable ladder to access an upper landing surface, how many
feet above the landing's surface must the side rails of the ladder extend?
A licensed manager - A licensed technician or salesperson shall only work under the
supervision of:
Privacy - What function describes a lockset that permits emergency access when
locked, but allows free egress?
Hook - Which pick is designed to pick one pin at a time?
Medeco - Which of the following brands of locks is considered "high security"?
5 - How many tumblers and springs are in a standard 5-cut key cylinder?
Holds the tumblers at the shear line - In lock picking, the tension wrench:
Two screws from the back of the cylinder - A rim cylinder is held in place by
Flat on both ends - What is the shape of a top pin?
Egress Side - Handling of doors for a lockset installation is referenced from the:
A+
14 - A Licensee who moves or changes employers shall notify the Oklahoma
Department of Labor within how many days?
High blood sugar - A technician is weak, having chills and cannot seem to get enough to
drink. What is the likely cause of the technicians symptoms?
Persons who sell, install, and service alarm systems - The Oklahoma Alarm and
Locksmith Industry Act applies to:
Short Wafer - What type of tumbler is most commonly used in a file cabinet lock?
$1000 - what is the maximum amount of administrative fines that can be levied against
any person for violations of the Oklahoma Alarm and locksmith Industry Act.
an overlapping astragal - A coordinator is required on a pair of fire doors having:
Carbide - With proper care, which cutter material typically provides the longest use?
Make the installation look better - Thru-bolt trim is used on many mortise locks to:
With the more stringent standard - If conflict exists between adopted references, the
reference that applies shall be the one:
Weiser - What brand of lock does a WR3 or 1054WB key blank fit?
A key is required to lock the room - A classroom function lock is designed so that:
Dexter - The key shown above matches
Bouncing the top pins above the shear line - Pick guns work by:
Weslock - What brand of lock does WK2 or 1175 key blank fit?
Master - What brand of lock does a M1 or 1092 key blank fit?
Requires a key or card from the outside in order to enter - A hotel function lockset is one
that:
Tension Wrench and Hook Pick - Which tools are used to manipulate a lock?
Screws on the inside of the knob - When removing a Kwikset entrance set, what should
the locksmith remove first?
, Improper lubricating the lock - Difficulty inserting or removing the key blank during
impressioning is caused by:
Brass - Of the following materials, which key blank produces the most obvious marks?
Locate a 3-pronged outlet - A power tool has a 3-pronged plug but the only available
outlets are 2-pronged. What should a technician do?
Three - How many trainees per job site can work under the supervision of a licensed
technician?
0.003 - What length of graduation is found in a standard universal pin kit with 0.115
diameter pins?
Insert the key change from the back of the wheel pack - When changing a Standard
Group 2 combination, the technician should dial the old combination on the change
mark and:
Is not lockable - A passage set is a lockset that
Hazardous vapors or fumes - What is the primary hazard when working with gas-
powered tools in an indoor space?
Three - When using a portable ladder to access an upper landing surface, how many
feet above the landing's surface must the side rails of the ladder extend?
A licensed manager - A licensed technician or salesperson shall only work under the
supervision of:
Privacy - What function describes a lockset that permits emergency access when
locked, but allows free egress?
Hook - Which pick is designed to pick one pin at a time?
Medeco - Which of the following brands of locks is considered "high security"?
5 - How many tumblers and springs are in a standard 5-cut key cylinder?
Holds the tumblers at the shear line - In lock picking, the tension wrench:
Two screws from the back of the cylinder - A rim cylinder is held in place by
Flat on both ends - What is the shape of a top pin?
Egress Side - Handling of doors for a lockset installation is referenced from the:
