AUTOMOTIVE COLLISION ASE PRACTICE EXAM
Technician A says that when replacing metal parts, an anti-corosion material should be
applied. Technician B says that some adhesive products may contain anti-corrosion
properties. Who is right?
A. A only
B. B only
C. Both A and B
D, Neither A nor B - Answers- C. Both A and B
Technician A says that humidity can influence the rate of corrosion. Technician B says
that cold temperatures can accelerate the rate of corrosion. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B - Answers- A. A only
Which of these is the best method to correct a filler weld with too little penetration?
A. Increase the stick-out and increase the wire feed
B. Increase the drive roll pressure and decrease the stick-out
C. Decrease the drive speed and increase the heat and wire feed
D. Increase the drive speed and decrease the stick-out - Answers- A. increase the
stick-out and increase the wire feed
Which of these tools should be used to metal finish a damaged panel?
A. Pick hammer and a vixen file
B. A grater and in-line sander
C. An electric sander with 16-grit sandpaper
D. A stud pin welder - Answers- B. A grater and in-line sander
Which of these characteristics would be the most noticeable difference when metal
finishing aluminum versus steel?
A. Work hardening
B. Ambient temperature
C. Location of damage
D. Alloy composition - Answers- D. Alloy composition
Technician A says that laminated glass may be used for the front windshield. Technician
B says that tempered glass may be used for door glass. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B - Answers- C. Both A and B
Which of these adjustments would be made if a door drops when it is opened?
, A. Move the lower hinge forward
B. Move the upper hinge forward
C. Move the striker upward
D. Move the upper hinge rearward - Answers- B. Move the upper hinge forward
The desired results of performing the hammer off dolly method during a dent repair is to
drive the:
A. low spot down and raise the adjacent high spot
B. high spot up and lower the adjacent low spot
C. low spot up and raise the adjacent high spot
D. high spot down and raise the adjacent low spot - Answers- D. high spot down and
raise the adjacent low spot
Which of these plastics can be heated to remove a minor buckle?
A. Thermoplastic
B. Carbon-fiber plastics
C. Fiberglass
D. Sheet molded compound - Answers- A. Thermoplastic
Technician A says that aplastic bumper may be repaired using plastic welding.
Technician B says that a plastic bumper may be repaired using an adhesive. Which is
right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B - Answers- C. Both A and B
When restoring sound deadeners and foam materials, the technician should:
A. use any material that is easy to install
B. create a dam to stop the foam so it can set up
C. allow the foam to run out of the relief hole
D. make sure the material is baked at 200 degrees F - Answers- B. create a dam to
stop the foam so it can set up
To remove vehicle parts that are attached with rivets, the technician should separate the
rivet head from the base by:
A. wrenching
B. drilling
C. hammering
D. heating - Answers- A. drilling
What process is commonly used to remove strain and tension on a sheet metal area
that has been damaged and severely stretched?
A. Hammer off dolly method
B. Hammer on dolly method
C. Paintless den repair
Technician A says that when replacing metal parts, an anti-corosion material should be
applied. Technician B says that some adhesive products may contain anti-corrosion
properties. Who is right?
A. A only
B. B only
C. Both A and B
D, Neither A nor B - Answers- C. Both A and B
Technician A says that humidity can influence the rate of corrosion. Technician B says
that cold temperatures can accelerate the rate of corrosion. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B - Answers- A. A only
Which of these is the best method to correct a filler weld with too little penetration?
A. Increase the stick-out and increase the wire feed
B. Increase the drive roll pressure and decrease the stick-out
C. Decrease the drive speed and increase the heat and wire feed
D. Increase the drive speed and decrease the stick-out - Answers- A. increase the
stick-out and increase the wire feed
Which of these tools should be used to metal finish a damaged panel?
A. Pick hammer and a vixen file
B. A grater and in-line sander
C. An electric sander with 16-grit sandpaper
D. A stud pin welder - Answers- B. A grater and in-line sander
Which of these characteristics would be the most noticeable difference when metal
finishing aluminum versus steel?
A. Work hardening
B. Ambient temperature
C. Location of damage
D. Alloy composition - Answers- D. Alloy composition
Technician A says that laminated glass may be used for the front windshield. Technician
B says that tempered glass may be used for door glass. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B - Answers- C. Both A and B
Which of these adjustments would be made if a door drops when it is opened?
, A. Move the lower hinge forward
B. Move the upper hinge forward
C. Move the striker upward
D. Move the upper hinge rearward - Answers- B. Move the upper hinge forward
The desired results of performing the hammer off dolly method during a dent repair is to
drive the:
A. low spot down and raise the adjacent high spot
B. high spot up and lower the adjacent low spot
C. low spot up and raise the adjacent high spot
D. high spot down and raise the adjacent low spot - Answers- D. high spot down and
raise the adjacent low spot
Which of these plastics can be heated to remove a minor buckle?
A. Thermoplastic
B. Carbon-fiber plastics
C. Fiberglass
D. Sheet molded compound - Answers- A. Thermoplastic
Technician A says that aplastic bumper may be repaired using plastic welding.
Technician B says that a plastic bumper may be repaired using an adhesive. Which is
right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B - Answers- C. Both A and B
When restoring sound deadeners and foam materials, the technician should:
A. use any material that is easy to install
B. create a dam to stop the foam so it can set up
C. allow the foam to run out of the relief hole
D. make sure the material is baked at 200 degrees F - Answers- B. create a dam to
stop the foam so it can set up
To remove vehicle parts that are attached with rivets, the technician should separate the
rivet head from the base by:
A. wrenching
B. drilling
C. hammering
D. heating - Answers- A. drilling
What process is commonly used to remove strain and tension on a sheet metal area
that has been damaged and severely stretched?
A. Hammer off dolly method
B. Hammer on dolly method
C. Paintless den repair
