SACA COMPLETE STUDY GUIDE TEST.
What is the pressure shown on this gauge?* - CORRECT ANSWER 500 kPa
What type of wrench is shown?* - CORRECT ANSWER Ratchet
What amount of power is used in this circuit?* - CORRECT ANSWER 96W
What type of geometric tolerance is shown in the feature control frame on this drawing? - CORRECT
ANSWER Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except? - CORRECT
ANSWER Machine operation procedures
What action must be taken to correctly position a dial caliper? - CORRECT ANSWER Sweep and rock to
the jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* - CORRECT ANSWER
Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing environment?*
0/4 - CORRECT ANSWER Moving a product from one station to another
What is the tolerance of the width of this part?* - CORRECT ANSWER +/-0.1
What do SDS sheets do?* - CORRECT ANSWER Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the proper torque? -
CORRECT ANSWER Stop turning the wrench
, What type of hole is identified by the arrow labeled A?* - CORRECT ANSWER Blind
What component does the schematic represent?* - CORRECT ANSWER Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 - CORRECT ANSWER General notes
What machine can be programmed to perform tasks in many different operations? - CORRECT ANSWER
Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - CORRECT ANSWER metal
Which of these is NOT a primary goal of a lean manufacturing system? - CORRECT ANSWER Greater
production volume
In the bolt designation shown, what is the pitch? - CORRECT ANSWER 2.5
What air pressure should be used when compressed air is used to clean or blow parts? - CORRECT
ANSWER Below 30 psi
If a machine stops unexpectedly due to a fault, which message tells you only that the machine has a
fault? - CORRECT ANSWER Warning message
What material condition does LMC define?* - CORRECT ANSWER Condition with the smallest amount of
material
What method do most small air compressors use to compress air - CORRECT ANSWER Piston movement
If an electronic sensor has a PNP type transistor, what effect does that have on the sensor's operations?
- CORRECT ANSWER Output signal goes high when the sensor is triggered.
What is the pressure shown on this gauge?* - CORRECT ANSWER 500 kPa
What type of wrench is shown?* - CORRECT ANSWER Ratchet
What amount of power is used in this circuit?* - CORRECT ANSWER 96W
What type of geometric tolerance is shown in the feature control frame on this drawing? - CORRECT
ANSWER Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except? - CORRECT
ANSWER Machine operation procedures
What action must be taken to correctly position a dial caliper? - CORRECT ANSWER Sweep and rock to
the jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* - CORRECT ANSWER
Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing environment?*
0/4 - CORRECT ANSWER Moving a product from one station to another
What is the tolerance of the width of this part?* - CORRECT ANSWER +/-0.1
What do SDS sheets do?* - CORRECT ANSWER Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the proper torque? -
CORRECT ANSWER Stop turning the wrench
, What type of hole is identified by the arrow labeled A?* - CORRECT ANSWER Blind
What component does the schematic represent?* - CORRECT ANSWER Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 - CORRECT ANSWER General notes
What machine can be programmed to perform tasks in many different operations? - CORRECT ANSWER
Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - CORRECT ANSWER metal
Which of these is NOT a primary goal of a lean manufacturing system? - CORRECT ANSWER Greater
production volume
In the bolt designation shown, what is the pitch? - CORRECT ANSWER 2.5
What air pressure should be used when compressed air is used to clean or blow parts? - CORRECT
ANSWER Below 30 psi
If a machine stops unexpectedly due to a fault, which message tells you only that the machine has a
fault? - CORRECT ANSWER Warning message
What material condition does LMC define?* - CORRECT ANSWER Condition with the smallest amount of
material
What method do most small air compressors use to compress air - CORRECT ANSWER Piston movement
If an electronic sensor has a PNP type transistor, what effect does that have on the sensor's operations?
- CORRECT ANSWER Output signal goes high when the sensor is triggered.
