TTT1 Study guide 100% Accurate!!
Who is the third party group that approves and endorses standards? -
ANSWERSAmerican National Standards Institute
What term is used to describe the documents written by members, or peers, in the
industry? - ANSWERSStandards
A company's health, safety and environment policy should be a combination of labor
regulations and ? - ANSWERSIndustry standards
Where OSHA has not promulgated specific standards, who is responsible for following
the acts general clause? - ANSWERSEmployer
On a job site who should be involved in the JHA process? - ANSWERSThe Whole Crew
What does the Term SOW stand for? - ANSWERSScope Of Work
The letters JHA stand for what ? - ANSWERSJob Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? -
ANSWERS3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the
wall does the case need to by to have the correct slope? - ANSWERS4
Work boots with ankle support are recommended for all work sites? - ANSWERSTrue
What do the letters PPE stand for ? - ANSWERSPersonal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? - ANSWERSSenses a short
circuit, prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ANSWERSEmployer
When using a y-lanyard attached to your back d-ring, at what height should the
connection to your anchorage be placed?extend? - ANSWERSShoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? -
ANSWERSNine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum
pull out distance? - ANSWERSFour feey
, What is the minimum force that a work positioning system anchorage must be able to
withstand? - ANSWERSTwo times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall
protection use? - ANSWERS5,000 lbs
When working, how often should fall protection equipment be inspected ? -
ANSWERSDaily before each use
According to the applicable industry standard, what is the minimum height from a lower
surface or ground where fall protection must be used? - ANSWERSSix feet
How many pounds force is one kilo Newton(kN) - ANSWERS225
What are the four most common types of towers used to support telecommunications
antennas? - ANSWERSGuyed towers, self-support towers, monopoles, and non-
standard
What identifies a self-support tower? - ANSWERSHorizontal member
What is not a component on a guyed tower? - ANSWERSGin pole
What is the purpose of a turnbuckle when working with guy wires? - ANSWERSAdjusts
the tension
Which government organization regulates tower lighting ? - ANSWERSFAA
When completing tower demolition, what must you have in place before you start the
job? - ANSWERSDemolition permit
When completing the visual inspection of a foundation, what is one of the key items to
look for? - ANSWERSCracks
What term identifies a monopole component? - ANSWERSBase flange
According to the manufacturers specifications, what is the minimum number of ground
kits installed on a single Run? - ANSWERSThree
What type of antenna is used to transmit signal from tower to tower? -
ANSWERSMicrowave dish
Where should a coax ground be placed vertically in relation to the hoisting grip? -
ANSWERSAbove it
When using tape and butyl to weatherproof a ground kit, what is a critical step in this
process ? - ANSWERSCut the tape when terminator
Who is the third party group that approves and endorses standards? -
ANSWERSAmerican National Standards Institute
What term is used to describe the documents written by members, or peers, in the
industry? - ANSWERSStandards
A company's health, safety and environment policy should be a combination of labor
regulations and ? - ANSWERSIndustry standards
Where OSHA has not promulgated specific standards, who is responsible for following
the acts general clause? - ANSWERSEmployer
On a job site who should be involved in the JHA process? - ANSWERSThe Whole Crew
What does the Term SOW stand for? - ANSWERSScope Of Work
The letters JHA stand for what ? - ANSWERSJob Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? -
ANSWERS3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the
wall does the case need to by to have the correct slope? - ANSWERS4
Work boots with ankle support are recommended for all work sites? - ANSWERSTrue
What do the letters PPE stand for ? - ANSWERSPersonal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? - ANSWERSSenses a short
circuit, prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ANSWERSEmployer
When using a y-lanyard attached to your back d-ring, at what height should the
connection to your anchorage be placed?extend? - ANSWERSShoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? -
ANSWERSNine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum
pull out distance? - ANSWERSFour feey
, What is the minimum force that a work positioning system anchorage must be able to
withstand? - ANSWERSTwo times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall
protection use? - ANSWERS5,000 lbs
When working, how often should fall protection equipment be inspected ? -
ANSWERSDaily before each use
According to the applicable industry standard, what is the minimum height from a lower
surface or ground where fall protection must be used? - ANSWERSSix feet
How many pounds force is one kilo Newton(kN) - ANSWERS225
What are the four most common types of towers used to support telecommunications
antennas? - ANSWERSGuyed towers, self-support towers, monopoles, and non-
standard
What identifies a self-support tower? - ANSWERSHorizontal member
What is not a component on a guyed tower? - ANSWERSGin pole
What is the purpose of a turnbuckle when working with guy wires? - ANSWERSAdjusts
the tension
Which government organization regulates tower lighting ? - ANSWERSFAA
When completing tower demolition, what must you have in place before you start the
job? - ANSWERSDemolition permit
When completing the visual inspection of a foundation, what is one of the key items to
look for? - ANSWERSCracks
What term identifies a monopole component? - ANSWERSBase flange
According to the manufacturers specifications, what is the minimum number of ground
kits installed on a single Run? - ANSWERSThree
What type of antenna is used to transmit signal from tower to tower? -
ANSWERSMicrowave dish
Where should a coax ground be placed vertically in relation to the hoisting grip? -
ANSWERSAbove it
When using tape and butyl to weatherproof a ground kit, what is a critical step in this
process ? - ANSWERSCut the tape when terminator
