VIVINT SMART HOME PRO (SHP) FINAL EXAM
QUESTIONS AND ANSWERS
ANSWER: 12-24V What is the input voltage range for the Doorbell Cam?
ANSWER: 16.5 VAC What is the output voltage of the transformer that
powers the SkyControl panel?
True - ANSWER True or False: When programming a sensor into the sky
panel, you can type the serial number or "learn" it by activating the device.
2. ANSWER When programming a DW21, what loop number is used?
123
Beans and wire caps. - ANSWER What materials can be used to group several
ground terminals in a takeover module?
Solder String Wire Caps
Duct Tape and Beans
True or False: When installing the fireman, it is needed to test the customer's
current smoke detectors.
ANSWER: 3/4” When installing a DW21, what size bit should be used to drill
the hole for the sensor?
1/2" 3/8" 3/4" 1"
True - ANSWER T or F: When installing the TAKE-345, make sure that the
transformer supplies power to the power supply before the battery.
True - ANSWER T or F: You must test signals from all secondary keypads and
key fobs, even if they are not detection devices.
False - ANSWER T or F: When running electricity to the TAKE-345, polarity is
not applicable.
, - ANSWER What is the proper height to put the PIR2?
Minimum height requirements: 5 ft, 7 ft, or 7.5 ft.
How would you program a CO3 that's mounted on a hallway wall?
Loop 1 Zone 8, Loop 1 Zone 14, Loop 3 Zone 4, and Loop 1 Zone 4 -
ANSWER.
When putting a DW21 into a metal door frame with a wooden door, what
materials should you use?
Metal Drill Bit
DW11 should be applied on all metal door frames.
3/4 inch insulated magnet
Eye goggles - ANSWER
True or False: Panic Pendants are programmed as an auditory alarm.
T or F: The Firefighter can be put adjacent to a standalone battery-powered
smoke detector.
Which of the following zone/sensor kinds is correct for programming an
SMKT3?
There are two types of freeze detection: Type 9 and Type 7.
Type 9 detects heat, Type 6 detects heat, Type 1 detects heat, Type 8 detects
freeze, Type 5 detects smoke, Type 7 detects smoke, and Type 9 detects smoke
(ANSWER).
Where is the authorized sensor location when installing a DW21?
Place anywhere within the door between 6" (15 cm) and 2' (61 cm) from the
floor.
Below 6" from the floor.
TOP OF THE DOOR - ANSWER
T or F: During a full system test, you may bypass any open doors or windows. -
ANSWER
T or F: When installing a translator, all of the current sensors must be
programmed as new equipment on the panel.
QUESTIONS AND ANSWERS
ANSWER: 12-24V What is the input voltage range for the Doorbell Cam?
ANSWER: 16.5 VAC What is the output voltage of the transformer that
powers the SkyControl panel?
True - ANSWER True or False: When programming a sensor into the sky
panel, you can type the serial number or "learn" it by activating the device.
2. ANSWER When programming a DW21, what loop number is used?
123
Beans and wire caps. - ANSWER What materials can be used to group several
ground terminals in a takeover module?
Solder String Wire Caps
Duct Tape and Beans
True or False: When installing the fireman, it is needed to test the customer's
current smoke detectors.
ANSWER: 3/4” When installing a DW21, what size bit should be used to drill
the hole for the sensor?
1/2" 3/8" 3/4" 1"
True - ANSWER T or F: When installing the TAKE-345, make sure that the
transformer supplies power to the power supply before the battery.
True - ANSWER T or F: You must test signals from all secondary keypads and
key fobs, even if they are not detection devices.
False - ANSWER T or F: When running electricity to the TAKE-345, polarity is
not applicable.
, - ANSWER What is the proper height to put the PIR2?
Minimum height requirements: 5 ft, 7 ft, or 7.5 ft.
How would you program a CO3 that's mounted on a hallway wall?
Loop 1 Zone 8, Loop 1 Zone 14, Loop 3 Zone 4, and Loop 1 Zone 4 -
ANSWER.
When putting a DW21 into a metal door frame with a wooden door, what
materials should you use?
Metal Drill Bit
DW11 should be applied on all metal door frames.
3/4 inch insulated magnet
Eye goggles - ANSWER
True or False: Panic Pendants are programmed as an auditory alarm.
T or F: The Firefighter can be put adjacent to a standalone battery-powered
smoke detector.
Which of the following zone/sensor kinds is correct for programming an
SMKT3?
There are two types of freeze detection: Type 9 and Type 7.
Type 9 detects heat, Type 6 detects heat, Type 1 detects heat, Type 8 detects
freeze, Type 5 detects smoke, Type 7 detects smoke, and Type 9 detects smoke
(ANSWER).
Where is the authorized sensor location when installing a DW21?
Place anywhere within the door between 6" (15 cm) and 2' (61 cm) from the
floor.
Below 6" from the floor.
TOP OF THE DOOR - ANSWER
T or F: During a full system test, you may bypass any open doors or windows. -
ANSWER
T or F: When installing a translator, all of the current sensors must be
programmed as new equipment on the panel.
